SERIES
TABLE OF CONTENTS
1
2
3
3.1.5 | Optional Bluetooth
& MP3 player boards
®
4
5
6
7
8
PACKAGE CONTENT
• 1 x Mixing console
• 1 x Mains cable with VDE plug
The warnings in this manual must be observed together with the "user manual - Section 2".
1 | INTRODUCTION
Thank you for choosing a A.N.T - Advanced Native Technologies - product!
In ANTMIX series of mixing consoles we have put our passion and our technological background gained over the years, to offer
products that meet your needs, and maintaining the quality over time.
All the models of this series represent a solution rich of features and optimally blend professional features with great quality and
exceptional value as: the advanced internal DSP with different effects and variations, the built-in compressor for main microphone
inputs, 60 mm faders as well as a series of I/O to fulfill a wide range of applications.
Both models feature a USB port, allowing connections to a computer or a tablet.
Specifically designed for an immediate and user friendly use, these mixers satisfy the needs of those who want an audio mixer
providing excellent performances, wide versatility of connections and controls as well as the best value for this range of products.
Please, dedicate some minutes to read this instruction manual in order to quickly achieve the best performances from this product.
For safety precautions, warranty and disposal, please refer to attached Section 2.
For further information about all A.N.T products catalog, please visit our website: www.ant-intomusic.com
2 | INSTALLATION
ANTMIX 16FX USB / 24FX USB models
are provided of:
A | Metal rough and light chassis.
B | ABS side panels with
ergonomic handle.
C | Front panel holes for optional boards
- MPX 1624 (MP3 player) or
BTX 1624 (Bluetooth
module)
®
ANTMIX Series
2
User manual |
• 1x User manual - Section 1
• 1x User manual - Section 2
A
A
B
B
3 | DESCRIPTION
3.1 | MIXER CONTROLS & CONNECTIONS
2
3.1.1 | MONO/STEREO INPUTS
2
3
1 MIC INPUT
3
3
1
2 MONO LINE INPUT - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
5
6
2
11
12
13
3 STEREO LINE INPUT - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
3
14
16
17
19
4
4 INSERT - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
5 GAIN & CLIP LED
5
6
6 COMP & LED - CHANNELS FROM 1 TO 6 (16FX USB) / FROM 1 TO 8 (24FX USB)
7
7 LOW CUT - CHANNELS FROM 1 TO 12 (16FX USB) / FROM 1 TO 20 (24FX USB)
8 EQ - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
C
C
8
XLR-F balanced microphone input.
6.35 mm. (1/4") balanced line input. You may also use an unbalanced cable.
Two 6.35 mm. (1/4") balanced line input.
Connecting only one cable to L/MONO, it becomes a mono channel. You can also use an
unbalanced cable.
6.35 mm. (1/4") TRS socket. This socket allows you to connect external devices (e. g. a
compressor, an EQ, etc.) to process the signal. For this connection use a "Y" cable, plugging
to this socket a TRS connector (tip = send, ring = return, and sleeve = ground) then connect
the external device with two TS connectors, one for input and one for the output.
This knob adjusts the gain of the microphone or line signal, turn it to the right to raise the
level, or to the left to decrease it.
The CLIP LED is lit when the input signal is too high.
This knob simultaneously adjusts compression threshold and ratio. Turning the knob hard left,
the compressor is turned off, turning to the right you activate it, until the maximum compression
to + 10. Use this control, for example, to make voices levels more homogeneous. The LED
next to the knob lights up when the compressor is activated.
This switch activates the hi-pass filter to reduce the frequencies from 75Hz down.
Use it to avoid that microphones connected to the input channels will pick up unwanted
signals rich of low frequencies.
Use this three-band equalizer to boost or to cut the high, mid and lo frequencies to get the
best mix in any environment. The semi-parametric FREQ. control allows frequency selection
from 100Hz to 8kHz.
ANTMIX Series
3
| User manual