Power Supply And Master Section - ADVANCED NATIVE TECHNOLOGIES ANTMIX 16fx usb Notice D'emploi

SERIES
12 GR 1-2
Press this button to route the channel signal to GROUP OUT 1-2 outputs.
12 12
13 GR 3-4
Press this button to route the channel signal to GROUP OUT 3-4 outputs.
14 L-R
14
Press this button to route the channel signal to MAIN MIX L-R outputs.
15
15 VOLUME
Use this fader to adjust overall channel volume.
16 SIG LED
16
This led is light when the input signal is very strong and it's close to distortion.
If the LED is continuously lit, you need to reduce the VOLUME of the fader or cut the channel EQ by
reducing the boost introduced by the HI-MID-LOW tone gains.

3.1.3 | POWER SUPPLY AND MASTER SECTION

1 2-TRACK IN
1
Unbalanced line input with RCA L/R sockets.
Connect to this socket the output of a hi-fi equipment (CD) or other device with RCA outputs.
2 2-TRACK OUT
Unbalanced line output with RCA L/R sockets.
2
Connect these outputs to a hi-fi device, e. g. a recorder; the volume is set by MAIN MIX output.
3 POWER LAMP
USB socket to power a lamp with a voltage of 5V - 500mA
3
4 PHONES
Output for connection to two headphones (A & B) with 6,35mm. (1/4") stereo jack.
4
5 CTRL/R
5 CONTROL ROOM output with two 6.35 mm. (1/4") line sockets.
This output section collects the signal from the CTRL ROOM SOURCE section. In studio applications
the typical use is for studio monitors but can also be used to drive a second group of powered speakers
with level control independent from the master, thus creating two distinct listening areas at different
volumes. The volume of this output is adjusted using the CTRL / ROOM knob regardless of the MAIN
MIX output levels
ANTMIX Series
6 User manual |
6 AUX SENDS 1, 2, 3 AND 4
6.35 mm. (1/4") output socket of relevant Aux sends 1, 2, 3 and 4.
6
7 GROUP OUTS 1, 2, 3 AND 4
7
Outputs of the respective groups on a 6.35 mm (1/4") balanced jack. These outputs allow to
drive a second group of amplified loudspeakers with level control independent from the master,
thus creating more distinct listening areas with different volumes or directing the selected
signals to a recorder / sound card.
8 DFX TO AUX 1 / AUX 2
8
These knobs set the signal level of the internal effects unit for AUX 1 and 2 sends.
Use them to increase or decrease the amount of processed signal.
9 TO DFX ST. OUT
This knob allows you to send the output of the internal
effects unit to rear panel dedicated output DFX ST OUT.
Connect this output to your external effects units, if any.
The output signal is the sum determined by the DFX
sends for each channel.
10 PROGRAM (PUSH)
This 100 position selector allows you to choose the
type of effect.
Turn the knob until you reach the desired program,
then press the knob to activate the selected effect.
The first 10 programs called ECHO reproduce the classic echo effect with increasing delay in the subsequent variants,
ECHO + VERB algorithms emulate a combination of echo and reverb, the impressive effect used in many musical
productions, the TREMOLO effects are mostly used on stringed instruments, while PLATE, CHORUS, and VOCAL programs
offer a pleasant sound widening and are ideal to strengthen vocals. The ROTARY effects simulate leslie organ, while the
SMALL ROOM programs reproduce the reverberation of rooms with similar dimensions to those of residential rooms,
alternating the simulation of reflective and absorbent walls. The FLANGER + REV section represents a combination of
effects perfect for different instruments, in particular keyboards, and finally the LARGE HALL effects package simulate
the reverberation of environments with large volumes characterized by mostly reflecting, naked walls.
11 DFX DISPLAY
This display shows the numbers corresponding to selected effects by the PROGRAM (PUSH) encoder.
12 PEAK
This LED is lit when the signal sent to DFX is too high, and there's a risk to saturate the internal effect. It's a good setting
of the effect sends when the LED flashes occasionally, only on signal peaks. When the LED remains continuously lit, it
is an indication of saturation. In that case please cut the volume of DFX POST channel sends.
13 DFX MUTE
This button allows you to enable or disable the return signal of the internal effects unit.
10 12 11
9
13
10
ANTMIX Series
| User manual
7