Analog Outputs; Digital Audio Input Ratings; Control Input/Output; Audio Performance - Tascam 102i Série Mode D'emploi

Line inputs (balanced)
SERIES 102i: 1-2
SERIES 208i: 1-2, 3-4
(when the input switch set to MIC/LINE)
Connectors: 6.3 mm (1/4 ") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Input impedance: 10 kΩ
Rated input level:
-54 dBu (0.0015 Vrms,
GAIN
+4 dBu (1.228 Vrms,
Maximum input level: +24 dBu (12.282 Vrms)
Gain range : 58 dB

Analog outputs

Monitor outputs (balanced, LINE OUT 1-2)
Connectors: 6.3mm (1/4") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 230 Ω
Nominal output level: +4 dBu (1.228 Vrms)
Maximum output level: +20 dBu (7.75 Vrms)
Line outputs (balanced, LINE OUT 3-8, on
SERIES 208i only)
Connectors: 6.3mm (1/4") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 230 Ω
Nominal output level: +4 dBu (1.228 Vrms)
Maximum output level: +20 dBu (7.75 Vrms)
Headphone outputs (PHONES
Connectors: 6.3mm (1/4") standard stereo jacks
Maximum output:
SERIES 102i: 18mW + 18mW
SERIES 208i: 45mW + 45mW
(THD+N 0.1% or less, into 32 Ω load)

Digital audio input ratings

OPTICAL (S/MUX) IN (SERIES 208i includes A
and B)
Connectors: OPTICAL (JEITA RC-5720C)
Signal format: Multi-channel optical format
(Supports S/MUX when 88.2 k, 96 k, 176.4 k or 192 kHz.)

Control input/output

USB
Connector: 4-pin USB B-type
Transfer rate: USB 2.0 High Speed (480 Mbps)
MIDI IN connector
Connector: 5-pin DIN
Format: standard MIDI
MIDI OUT connector
Connector: 5-pin DIN
Format: standard MIDI
WORD IN connector (SERIES 208i only)
Connector: BNC
Input voltage: 2.0 Vpp - 5.0 Vpp
Input impedance: 75 Ω ±10%
Permitted frequency deviation during external synchronization:
±100 ppm
Terminal on/off switch
GAIN knob at maximum)
knob at minimum)
/ )
WORD OUT connector (SERIES 208i only)
Connector: BNC
Input voltage: 2.0 Vp-p (into 75 Ω)
Output impedance: 75 Ω ±10%
Sampling frequencies: 44.1, 48, 88.2, 96, 176.4 and 192 kHz

Audio performance

Mic amp EIN (equivalent input noise)
-129 dBu or lower
Frequency response
MIC/LINE IN
At 44.1/48 kHz, 20 Hz - 20 kHz: +0 dB/-0.4 dB (JEITA)
At 88.2/96 kHz, 20 Hz - 40 kHz: +0 dB/-0.8 dB (JEITA)
S/N ratio
109 dB
MIC/LINE IN GAIN
( , knob at minimum, 20 kHz SPCL LPF+A-Weight)
110 dB
LINE OUT MONITOR
( , knob at maximum, 20 kHz SPCL LPF+A-Weight)
THD + N
SERIES 102i
0.0016%
MIC IN
( , 1 kHz sine wave,
SPCL LPF)
0.0023%
LINE IN
( , 1 kHz sine wave,
SPCL LPF)
0.0014%
LINE OUT
( , 1 kHz sine wave,
kHz SPCL LPF)
SERIES 208i
0.0013%
MIC IN
( , 1 kHz sine wave,
SPCL LPF)
0.0019%
LINE IN
( , 1 kHz sine wave,
SPCL LPF)
0.0014%
LINE OUT
( , 1 kHz sine wave,
kHz SPCL LPF)
Crosstalk
100 dB or more
MIC/LINE LINE OUT
( , 1kHz sine wave,
w
mum)
TASCAM SERIES 102i / SERIES 208i
GAIN
knob at minimum, 20 kHz
GAIN
knob at minimum, 20 kHz
MONITOR
knob at maximum, 20
GAIN
knob at minimum, 20 kHz
GAIN
knob at minimum, 20 kHz
MONITOR
knob at maximum, 20
GAIN
knob at mini-
15