Teac HA-P5 Mode D'emploi page 8

Note about switching input sources
This unit does not have a switch to set the input connector.
The input will be selected automatically in the following order
of priority.
Priority Connector
PC connector, iPod/iPhone/iPad connector
High
o First connected is activated
Low OPT/COAX IN and LINE IN connector
o To use digital or analog audio input, disconnect the PC and
iPod/iPhone/iPad connectors.
o Use the OPT COAX/LINE INPUT switch on the side of the unit
to enable digital or analog input.
o When digital audio is input, the unit will automatically switch
between optical and coaxial connection.
Using the TEAC Global Site
You can download updates for this unit from the TEAC Global
Site: http://teac-global.com/
1) Open the TEAC Global Site.
2) In the TEAC Downloads section, click the desired language
to open the Downloads website page for that language.
NOTE
If the desired language does not appear, click Other
Languages.
3) Click the "Search by Model Name" section to open the
Downloads page for that product. (Users in Europe should
click the product name in the "Products" section instead.)
4) Select and download any updates that are needed.
8
Download the latest firmware
Please visit the HA-P5 product page from the TEAC Global Site
and download the latest firmware.
(If no firmware is listed, no firmware update is available.)
http://teac-global.com/
Troubleshooting
If you experience a problem with this unit, please check the
following items before requesting service. If it still does not
operate correctly, contact the retailer where you purchased
the unit.
The unit does not turn on.
e If the remaining battery charge is too low, the unit will
not turn on. Supply power to the unit through the DC IN
5V connector or the PC connector.
e Has the automatic power saving function put the unit to
sleep? Turn the power/volume knob counterclockwise
to turn the unit off once.
No sound is output.
e Use the power/volume knob to adjust the volume.
e Confirm that the connected device is playing back.
e Confirm the headphones jack connection.
Specifications
Headphone output
Frequency response . . . . . 10 Hz–100 kHz (when using LINE IN)
Supported headphone impedance . . . . . . . . . . . . . . . . . 16–600 Ω
Effective maximum output
160 mW + 160 mW (32 Ω, 1 kHz,10%, JEITA)
60 mW + 60 mW (300 Ω, 1 kHz,10%, JEITA)
30 mW + 30 mW (600 Ω, 1 kHz,10%, JEITA)
Line input
Maximum input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Vrms
Line output
Frequency response . . . . . . .10 Hz–80 kHz (when using LINE IN)
Maximum output level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Vrms
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0°C to 35°C
Battery operation time
(when load is 32 Ω and output is 0.1 mW + 0.1 mW)
Apple iOS device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .About 5 hours
o The operation time when using batteries will differ
depending on use and other conditions.
Charging time . . . . . . . . . . About 4 hours (using DC power supply)
External dimensions
65.4 × 121.4 × 21.6 mm (2 5/8" × 4 7/8" × 7/8")
(W × D × H, not including protrusions)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 g (1/2 lb)
Supported sampling frequency/bit depth
PCM: up to 192 kHz/24-bit
DSD: 5.6448 MHz maximum
o Design and specifications are subject to change without
notice.
o Weight and dimensions are approximate.
o Illustrations may differ slightly from production models.