RAVAK SABINA 80 Instructions De Montage page 3

GB
INSTALLATION INSTRUCTIONS FOR SABINA, SABIUS COVERING PANEL
ATTENTION: When installing the supportive legs for this shower tray equipped
with a covering panel, these installation instructions need to be followed! Use the
parts from the BASE mounting kit together with the parts from the panel kit for this
installation.
INSTALLATION:
1.
Place the shower tray upside down on a soft mat. Attach the threaded rods
(M 12x360) into the end openings of the metal supportive bearers
threaded rods at the bearer ends that have the two 12.5 mm dia. holes). Attach
the shorter threaded rods
holes on the bearers as depicted in
end of one of the bearers, attach one remaining threaded rod
with the plastic legs as depicted in 4
a plastic leg) with the remaining bearer. Do not tighten the nuts.
2. Place the metal bearers on the reinforced bottom of the shower tray in such a
way that the threaded rod serves as a support for the seat, and that the ends of
the bearers are close together beneath the seat area and wide apart at the outer edge of the tray. Following
bearers in such a way that the outside threaded rods reach 45 mm from the outer edge of the shower tray and approx. 500 mm
from each other. Trace the outlines of the bearers on the bottom of the tray and mark out the dia. 6 mm mounting openings.
Set the bearers aside and using a dia. 3 mm drill bit, drill the mounting openings maximum 10 mm deep. ATTENTION, drill
only into the reinforced bottom of the shower tray and use a backstop to prevent drilling the tray bottom through!
3. Apply a layer of silicon putty under the horizontal edges of the bearers to level the surface, and attach the bearers using the
screws (dia. 5.5 x 16 mm). 6
4. Likewise, apply a small amount of the putty on top of the seat-supporting leg where it makes contact with the underside of the
seat of the shower tray. Use gentle pressure to tighten this supportive leg under the seat area and secure it tight with a nut.
5. Screw the nuts 103 and the covering panel
6. Insert the metal threaded rod support
the metal support on the shower tray.
7. Loosen the threaded rod
shower tray rim to balance and stabilize the position of the threaded rod support.
8. Insert the metal threaded rod support
support 105 in their correct position by reasonably tightening the nuts. Tightening of the nuts must NEVER DEFORM THE
SHOWER TRAY RIM!
9. Under the edge of the rim, there are the covering panel holders
for the covering panel and in their upper part there is a shaped spring for the trim of the covering panel to be pushed in. Check
and adjust if necessary, the position of both panel holders
edge, and so that its shape matches the outer profile of the shower tray.
10. Turn the shower tray the correct way up and set it in its correct location. Measure the height of the plastic covering panel
(nominally 385 mm). According to its actual height, adjust the height of the shower tray, so that this dimension to under the rim
equals the height of the plastic covering panel (+ 2-3 mm tolerance). Mark out the height of the rim as well as height of the
upper rim of the tray on the adjacent bathroom walls.
11. Try to put the covering panel to the mounted panel holders, push it into the holder
outline. Trace the outline of the panel on to the floor and trace the shape of the shower tray sides on the adjacent walls. Take
the panel off and if necessary, adjust the height of the shower tray some more by twisting the plastic legs. Tighten the securing
nuts of the legs.
12. Set the tray aside and mark out the height of the shower tray upper rim on the walls in the marked position. Following the
installation instructions for the shower tray, dimension and attach the plastic mounting clips on the wall.
13. To stabilize the lower part of the covering panel, mount the spring
bottom part of the threaded rod
moving it about the threaded rod so it acts as a backstop. Tighten the lower nuts
14. To fix the covering panel at the sidewalls, use two holders
Following the pic.4, set the panel holder to the drawn outline of the panel 50 mm and 330 mm high. Move the holder
approximately 3-4 mm (as much as the thickness of the panel) inwards under the shower tray, and mark out on the wall the
centers of the oval fixing holes. At these points, drill dia. 8 mm holes and insert the plugs
with screws 110. Mark out the axis of the two panel holders both on the panel and on the wall.
15. Mount the waste pipe/siphon on the shower tray.
16. Set the shower tray in its final position and mount it on the plastic clips as described in the installation instructions for the
shower tray. Attach the plastic covering panel and balance it. Mark out on the panel the centers of mounting openings for the
panel side holders 108 (in the center of the perforated metal sheet).
17.
Use a dia.3 mm drill bit to drill the panel through (together with the perforated metal sheet). BE CAREFUL not to damage the
plastic panel with the drill chuck! Attach the panel with the self-tapping screw
plastic covering cap 113
18. Use the Ravak silicon putty to seal the gaps between the shower tray and the tiling. By using some other product to do the
sealing you run a risk of water leakages. To fill in some bigger gaps, we recommend you to use the plastic covering strips. If
necessary, seal also the gaps between the covering panel and the tiles (
tel.: 318 427 111, 318 427 200, fax: 318 427 269, 318 427 278, e-mail: smith@ravak.cz, www.ravak.com
2 (M 12x125 mm) with the plastic legs into the other
pic.2 (the opposite way round) To the other
pic.3. Attach the M 12 x 125 thread rod (with
3
104 on the bolts
105 into the shower tray rim and set it upright towards the bearer. Trace the outline of
102 and the threaded rod support. Apply a sufficient amount of silicon putty into the underside of the
105 in its previous place into the putty. Fix the threaded rod
102. Following the outline of the covering panel drawn on the floor, adjust the spring
as depicted in pic.4 .
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR
101 Front panel
102 Threaded Rod M12 x 360 mm
103 Nut M12
102
104 Panel Holder Upper 15
1 (attach the
105 Thread Rod Support 17
106 Panel Holder 10
107 Washer Ø 13
108 Side Panel Holder 20
.
109 Plug Ø 8
3
(330 mm long)
110 Screw For The Plug Ø 4x40
111 Self-tapping screw 3.5x13
112 Plastic Washer Ø 4
113 Plastic Covering Cap
102 as depicted in pic.2.
104 on the threaded rods. Their lower part serves as a support
104 , so that the covering panel is mounted close under the rim
106, washer 107
103.
108 for the left edge of the panel and two for the right one.
111 and the plastic washer
pic.5)
.
MOUNTING SET PANEL
MOUNTING SET PANEL KIT
pic.1
102 and the threaded rod
104, and adjust it to the shower tray
and the nut 103 onto the end of the
109, and screw the panel holders
112 , and push on the
1 pc
2 pcs
10 pcs
2 pcs
2 pcs
2 pcs
2 pcs
4 pcs
8 pcs
8 pcs
4 pcs
4 pcs
4 pcs
, move the
101
106 by
108