Roller E-Control Notice D'utilisation page 7

eng
valve, and open the (7) „Test" stop valve. Switch in the pump (1), and pump
the fluid.
3.3. Finalizing the operation of the unit
After finalizing the operation of the unit, open both the (8) „Press"
pressure-regulating valve and the (7) „Test" stop valve. Subsequently, rinse the
pump with clean water for a few minutes.
4. Servicing
4.1. Inspecting the unit
Before inspecting the unit, draw out the mains plug! Before every using of the
machine, examine the high-pressure-hose for damages. Keep clean the (4)
suction filter!
4.2. Maintaining the unit
Before maintaining the unit, draw out the mains plug! Change the oil after every
150 operating hours. For this, lay the pressure-testing pump on its side area,
detach the (11) screws at both the housing shells. Then, open and detach the
housing shells. Open the (12) plastic-material plug fittings at the bottom side
of the pump. Drain-off the oil. Now, fill in approx. 0.15 l of new SAE-30 oil. When
the pump is leaking oil, the complete pressure-testing pump must be sent for
inspection and/or repair to a service station authorized by ROLLER.
4.3. Repairing the unit
Before repairing the unit, draw out the mains plug! This work may only be carried
out by skilled labor and trained personnel as well.
5. Instructions for eliminating malfunctions
5.1. Malfunction: The pressure-testing pump is running. However, it is
not creating any pressure.
Cause:
● The „Press" stop valve has not been closed yet.
● The pressure-testing pump has been sucking air.
● The filter at the suction hose has been plugged.
● The pressure-testing pump has become defective.
5.2. Malfunction: The pressure at the manometer is varying irregularly.
Cause:
● There is air in the system.
5.3. Malfunction: The motor does not start working. It is humming.
Cause:
● The pump has been locked.
● There is an inappropriate voltage supply (is there an appropriate
extension cable?).
5.4. Malfunction: When operating, the motor suddenly dies.
Cause:
● The motor protective switch has disconnected it.
● The pump has got hot, or is blocking.
6. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to the
first user but shall be a maximum of 24 months after delivery to the Dealer. The
date of delivery shall be documented by the submission of the original purchase
documents, which must include the date of purchase and the designation of
the product. All functional defects occurring within the warranty period, which
are clearly the consequence of defects in production or materials, will be
remedied free of charge. The remedy of defects shall not extend or renew the
guarantee period for the product. Damage attributable to natural wear and tear,
incorrect treatment or misuse, failure to observe the operational instructions,
unsuitable operating materials, excessive demand, use for unauthorized
purposes, interventions by the Customer or a third party or other reasons, for
which ROLLER is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station autho rized by ROLLER
without prior interference in an unassembled condition. Replaced products and
parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of users, in particular the right to claim damages from the
Dealer, shall not be affected.
7. EC declaration of conformity
ROLLER declares that the products decribed in this user manual comply with
corresponding directives 2004/108/EG, 2006/42/EG and 73/23/EWG. Corre-
spondingly this applies to the following norms: DIN EN ISO 12100-1, DIN EN
12348, DIN EN 50144-1, DIN EN 55014-1, DIN EN 55014-2, DIN EN 60204-1,
DIN EN 60335-1, DIN EN 60335-2-45, DIN EN 60745-1, DIN EN 60745-2-9,
DIN EN 60745-2-11, DIN EN 61000-3-2, DIN EN 61000-3-3, DIN EN 61029-1,
DIN EN 61029-2-9, DIN/ISO 3744.
Waiblingen, 01. 08. 2010
Albert ROLLER GmbH & Co KG
Manufacturer of Tools and Machines
D-71332 Waiblingen
Rainer Hech
8. Spare parts lists
For spare parts lists, see www.albert-roller.de under Downloads → Parts lists.
eng