Maintenance And Service; Maintenance And Cleaning; Accessories - Bosch PCM 8 S Notice Originale

OBJ_BUCH-557-005.book Page 35 Tuesday, July 5, 2011 4:08 PM
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the machine into the transport position.
– Turn the saw table 17 until it engages at 0°.
Checking: (see figure U1)
– Set an angle gauge to 90° and place it on the saw table 17.
The leg of the angle gauge must be flush with the saw blade 8
over the complete length.
Adjusting: (see figure U2)
– Loosen the lock lever 31.
– Loosen the lock nut of the stop screw 22 using a commer-
cial box-end or open-end spanner (size 10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever 31 again.
– Afterwards, retighten the lock nut of the stop screw 22
again.
In case the angle indicator 53 is not in a line with the 0° mark
of the scale 63 after the adjustment, loosen the screw 64 us-
ing a commercial Phillips screwdriver and align the angle indi-
cator along the 0° mark.
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the working position.
– Turn the saw table 17 until it engages at 0°.
– Loosen the clamping lever 31 and tilt the tool arm leftward
to the stop (45°) by the handle 5.
Checking: (see figure V1)
– Set an angle gauge to 45° and place it on the saw table 17.
The leg of the angle gauge must be flush with the saw blade 8
over the complete length.
Adjusting: (see figure V2)
– Loosen the lock nut of the stop screw 21 using a commer-
cial box-end or open-end spanner (size 10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever 31 again.
– Afterwards, retighten the lock nut of the stop screw 21
again.
In case the angle indicator 53 is not in a line with the 45° mark
of the scale 63, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Aligning the Fence
– Bring the machine into the transport position.
– Turn the saw table 17 until it engages at 0°.
Checking: (see figure W1)
– Set an angle gauge to 90° and place it on the saw table 17
between the fence 10 and the saw blade 8.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting: (see figure W2)
– Loosen all Allen screws 33 with the Allen key 20 provided.
– Turn the fence 10 until the angle gauge is flush over the
complete length.
– Retighten the screws again.
Bosch Power Tools
Aligning the Angle Indicator (Horizontally) (see figure X)
– Bring the machine into the transport position.
– Turn the saw table 17 until it engages at 0°.
Checking:
The centre line of the angle indicator 14 must be in line with
the 0° mark of the scale 15.
Adjusting:
– Loosen the screw 65 using a commercial Phillips screw-
driver and align the centre line of the angle indicator along-
side the 0° mark.
– Retighten the screw again.
Transport (see figure Y)
Before transporting the power tool, the following steps must
be carried out:
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Carry the machine by the transport handle 26 or hold it by
the recessed handles 34 on the sides of the saw table.
The power tool should always be carried by two per-
sons in order to avoid back injuries.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains
plug.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Clean the roller 9 and the lighting and laser unit (24, 23) reg-
ularly.

Accessories

Dust bag set. . . . . . . . . . . . . . . . . . . . . . . . . . . 2 605 411 222
Extension bars . . . . . . . . . . . . . . . . . . . . . . . . 2 607 001 978
English | 35
1 609 929 U68 | (5.7.11)