Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 6
III
SPRING TOY - VEERSPEELTUIG - JEU À RESSORT
FEDER FIGUR- FIGURA RESORTE - FIGURA MOLLA - BUJAK
1
C
2x
3
A
1x
26
ASSEMBLY - MONTAGE - MONTAJE - MONTAGGIO - MONTA
2
D
2x
4
E
2x
2
17

ASSEMBLY STEPS

Please see illustrations at the end of the manual for further assembly instructions.
I
Assembly of spring:
1. Place the fi rst round plate between the spring.
2. Turn the round plate towards the bottom of the spring.
3. Place the black distance cube in front of the round plate, at the bottom between the spring and screw down the round
plate until the black distance cube is blocked.
4. Assemble the spring onto the anchor by using hardware set nr. 4. Tighten the 3 bolts by hand only.
5. Click the round plate onto the spring by blocking the anchor (for example: with your feet) and turning the spring when
holding it at the top. You'll hear a small click when the round plate clicks into position.
6. Screw on the bolts with the ratchet spanner.
7. Place the second round plate between the spring.
8. Turn the round plate towards the top of the spring.
9. Place the black distance cube in front of the round plate, at the top between the spring and screw down the round plate
untill the black distance cube is blocked.
10. Assemble the U-connection onto the spring by using hardware set nr. 4. Tighten the 3 bolts by hand only.
11. Click the round plate onto the spring by blocking the anchor (for example: with your feet) and turning the U-connection.
You'll hear a small click when the round plate clicks into position.
12. Screw on the bolts with the ratchet spanner.
IIa Assembly of spring and fl at anchor:
1. Find a suitable location to install the spring animal. See FIG II. After installation the concrete foundation will need to be
covered with a shock absorbing surface. The use of rubber tiles is recommended.
2. Place the concrete anchor horizontally, using the spirit level, at the desired location and mark the holes.
3. Drill the 4 holes of 90 mm deep.
4. Remove the dust out of the drilled holes.
5. Put the 4 wedge anchors in the holes.
6. Screw on the nuts of the 4 wedge anchors with the ratchet spanner.
IIb Assembly of spring and concrete anchor:
1. Find a suitable location to install the spring animal. Do not dig holes in loose soil or sand. The soil should be stable and
compacted to provide proper support. See FIG II.
2. Dig a hole for the anchor of the metallic spring pedestal. The hole needs to be 700 mm wide at the bottom and 400 mm
deep.
3. Flatten the bottom of the hole and stamp with your feet. Place the metallic spring pedestal straight up in the hole. The
best way is to use a spirit level. You can fi x this position by putting a heavy stone or brick on the lower plate.
4. Mix enough concrete to fi ll the hole. Be careful to follow the manufacturers instructions. Pour concrete into the hole. Be
careful to keep the spring and upper side top plate free of concrete. Make sure the spring is straight using a spirit level.
5. Allow concrete to set overnight before going to step 6.
6. Cover the visible concrete with soil so that the complete ground level is fl at again. Make sure the ground is covered in
a suitable way (eg. rubber tiles, bark, wood chips,...).
III Assembly of the spring toy:
1. Place the 2 side panels with insert in the U-connection.
2. Place the 2 other side panels in the U-connection.
3. Slide the spring toy between the side panels in the U-connection.
4. Assemble the total onto the U-connection by using hardware set 2.
5. Screw the seat on the spring toy by using hardware set 3.
6. Assemble the handles and feet supports by using hardware set 1. The handles and feet supports need to be fi rmly fi xed
so that it's impossible to rotate them.
7. Put on all bolt covers. Remark: use the correct dimension of bolt cover for the handles and foot supports.
Remark: The soil under the spring animal requires an adjusted surface that is shock absorbing!
assembly steps
p. 22 - 23
p. 26 - 27
Instructions for use - M173xx.04 - spring toys HDPE - 'graphics'
p. 24
p. 25
3

Publicité

Table des Matières
loading

Table des Matières