Product Description And Specifications - Bosch PSA 900 E Notice Originale

Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for reciprocating saws
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it un-
stable and may lead to loss of control.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Ensure that the footplate is always resting on the
u
workpiece while sawing. The saw blade can jam and
lead to loss of control over the power tool.
When the cut is completed, switch off the power tool
u
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the power tool securely.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side
u
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
Ensure that the material is securely clamped. Do not
u
support the workpiece using your hands or feet. Do
not touch any objects or the floor with the saw while it
is running. There is a risk of kickback.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
Bosch Power Tools
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is suitable for sawing wood, plastic, metal
and building materials on a firm surface. It is suitable for
straight and curved cuts. When using designated suitable bi-
metal saw blades, flush cutting is also possible. The saw
blade recommendations are to be observed.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
A)
(1) Saw blade
(2) Base plate
(3) Saw blade receptacle
(4) SDS lever for saw blade release
(5) On/off switch
(6) Handle (insulated gripping surface)
(7) Clamping plate
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating saw
Article number
Stroke rate control
Rated power input
No-load stroke rate n
0
Tool holder
Stroke
Max. cutting depth
– in wood
– in steel (unalloyed)
– Pipe diameter
Weight according to
EPTA‑Procedure 01:2014
English | 11
PSA 900 E
PSA 9000 E
3 603 CA6 0..
●
W 900
−1
min 0–2700
SDS
mm 28
mm 200
mm 20
mm 150
kg 3.5
1 609 92A 66M | (11.11.2020)