CDVI CA-A470-A Manuel D'installation page 4

MANUEL D'INSTALLATION
CA-A470-A
2-Door expansion module
Figure 3: Setting the A+ and B- jumpers
Jumpers
set to LOW
A+ B-
LOW
HIGH
350mA/700mA Battery
Charging Jumper
The 350mA/700mA Jumper allows you to
select the charging current for the backup
battery of the 2-Door Expansion Module.
Charging the battery at 350mA takes
longer, but consumes less power. Charging
the battery at 700mA takes less time, but
consumes more power.
Figure 4: Setting the 350mA/700mA jumper
Jumpers
set as 350mA
Programming in Centaur
Using the Centaur Access Control Software,
program the inputs, outputs, readers, and
keypads connected to the 2-Door Expansion
Green "lock#1" and "lock #2" LEDs:
ON = Relay activated.
CA-A470-A
2-Door Expansion Module
LOCK#1
STATUS
D1NC
COM
JP120
LOCK#2
D1NO
350mA/700mA
D2NC
COM
D2NO
Z1
COM
Z2
Z3
COM
READER#2
Z4 BACKUP
DATA
2 1
0 0 NO CARD
0 1 2 CARDS
1 0
ALL CARDS
1 1 UNLOCK DOOR
Green "reader#2 data" and "reader#1 data" LED:
Long fl ash = Receiving card read
Short fl ash = Receiving card read, but the system
does not recognize the card's format
OFF = Not receiving card read
www.cdvi.com
4
www.cdvigroup.com
Jumpers
set to HIGH
A+ B-
LOW
HIGH
Jumpers
set as 700mA
Figure 5: CA-A470-A indicators
Green "STATUS" LED:
Flash = Module OK
Slow fl ash = Communication failure
(see also "comm" LED)
+
AC OK
AUX OK
COMM
CHECK BATT
BATT TRBL
SWITCH
ADD 1
SW1
SW2 ADD 2
SW3 L1Energize
L2Energize
SW4
SW5 BACKUP1
SW6 BACKUP2 LOW HIGH
SW7 PULSE 5&6 B-
SW8 N/D
A+
READER#1
DATA
EOL
TX RX
E-BUS
Module. The options are explained in the
Centaur Access Control Software Reference
Manual. Centaur will identify the 2-Door
Expansion Module by its address, DIP
Switches 1 & 2, and will recognize the
devices as follows:
Doors
Keypad/Reader 1
Keypad/Reader 2
Inputs
Z1
Z2
Z3
Z4
Outputs
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
Doors cannot be defi ned as Door Type Elevator
(Door Properties window, General tab, Door
Type: Elevator) and the module does not
support Interlock Inputs (Door Properties
window, Inputs and Outputs tab,
Interlock Input).
Other modules in the system cannot activate
the 2-Door Expansion Module's outputs.
The 2-Door Expansion Module does not support
Zone Doubling (see Figure 6).
AC
AC
BAT+
BAT-
V+
V+
V-
V- Red "tx" LED and
OUT5
OUT6 green "rx" LED:
ON =
Communication
A+
B-
OK (may fl icker)
GND
TMP
OFF =
TMP
Communication
failure
Address 1 Address 2 Address 3
Door 3 Door 5 Door 7
Door 4 Door 6 Door 8
Input 17 Input 21 Input 25
Input 18 Input 22 Input 26
Input 19 Input 23 Input 27
Input 20 Input 24 Input 28
Output 7 Output 13 Output 19
Output 8 Output 14 Output 20
Output 9 Output 15 Output 21
Output 10 Output 16 Output 22
Output 11 Output 17 Output 23
Output 12 Output 18 Output 24
Green "AC OK" LED:
ON = AC power
OFF = Power failure
Green "AUX OK" LED:
ON = Auxiliary power
OFF = Auxiliary power failure
Red "COMM" LED:
ON = Communication failure
OFF = OK
Green "CHECK BATT" LED:
ON = Battery verifi cation in
progress (every minute)
Red "BATT TRBL" LED:
ON = Battery low or disconnected