in-lite FLH-LED008 Manuel D'utilisation page 4

EN
Contents
1x FLH-LED008/009 12 V / 2 W
Dimensions 100 x 100 mm / 3.9 x 3.9 inches
Overall height 70 mm / 2.8 inches
1x Easy-Lock
4x screw for attachment to wood
1x Torx key
Material
Impact-resistant polycarbonate filled with a 2-component resin
Stainless steel cover plate
Please read the following instructions before installing. You are
advised to keep these installation instructions in a safe place.
Although a 12 V system is safe, we advise you to have a qualified
electrician check the installation.
Use
Integrated atmospheric lighting suitable for illuminating plants (small
trees, ornamental trees) or as lights marking a pathway, patio, pond
edge, driveway etc.
Lamp
The fixture is equipped with a high-quality LED lamp. These lamps have
a long life (about 50,000 hours) and a high light output and their power
consumption and the heat produced are extremely low.
Important!
Never connect the low-voltage cable directly to a 100-240 V power
source. It is only suitable for use in combination with a 12 V low-voltage
system. This product should only be used within the in-lite system.
Use of products other than those made by in-lite will invalidate the
warranty.
Enjoy the lighting in your yard.
EN
Connecting the fixture to 12 V
The already installed lamp means the fixture is immediately ready for
use. Therefore you do not need to install the lamp first. This fixture can
be built into various sorts of decorative paving, such as concrete or
natural stone, or wooden constructions such as decking, walls, fenc-
es, pond edges etc.
Step 1a (concrete, stone and similar)
Replace a 100 x 100 mm / 3.9 x 3.9 inch stone with this fixture or, in the
case of large, unbroken surfaces, saw out a 100 x 100 mm / 3.9 x 3.9
inch piece. The fixture can then be placed directly on the underlying
sand bed. (Go to step 3.)
Step 1b (wooden structures)
Remove the plastic housing by unscrewing the Torx bolts on the top
of the fixture. Then saw a hole of 60 x 40 mm / 2.4 x 1.6 inches and about
20 mm / 0.8 inches deep (the LED unit fits into this).
Step 2b
Feed the connector for the fixture through the hole and then carefully
insert the fixture into the recess. Attach the fixture with the wood
screws provided. (Fig. 1)
Step 3
Join the Easy-Lock connector to the main cable. (Fig. 2)
a. There are two cable grips. The grip with the wider recess fits the
10/2 main cable, the grip with the narrower recess fits the 14/2
main cable. Clamp the correct cable grip over the main cable.
b. Put the cable grip (with the cable underneath) in the Easy-Lock
connector.
c. Tighten the threaded cap on the Easy-Lock connector. This will
cause the contacts to be pushed through the insulation on the ca-
ble. In tightening the cap, a little gel is applied to the contacts in the
Easy-Lock connector. This serves to protect the contacts against
moisture. A little gel may possibly come out of the Easy-Lock con-
nector: so after installation (and/or before a meal), wash your
hands with soap and water, and avoid the gel coming into contact
with your eyes.
Step 4
Connect the power cable to the fixture by connecting the mini-
connector. (Fig. 3)
If the lamp does not work correctly, check that the Easy-Lock connec-
tor is properly connected to the main cable. Do the same for the mini-
connector. Repeat steps 3 and 4. When the fixture is connected to the
main cable also check that the contacts of the Easy-Lock connector
are not bent. If you have any problems, contact your dealer.
General maintenance advice
We advise wiping the fixture down at least once a year using a clean
cloth and warm water.