Di-soric LAT 61 Série Manuel D'instructions page 8

8
● Power voltage: 24V DC
● Ambient temperature: 20°C
● Sampling cycle: 500μs
● Number of measurement values used for averaging: 1024
● Measurement object: white ceramic
Model No. Standard type
Measurement method
Measurement center distance
Measuring range
Beam source
Beam dimensions
1
Beam receiving element
Resolution
Linearity
Temperature characteristics
Supply voltage
Current consumption
Sampling cycle
Analog output voltage
Analog output current
OUT1
OUT2
OUT3
Output operation
Short-circuit protection
NPN/PNP type switching input
Timing input
Multifunction Input
Laser radiation indicator
Alarm indicator
Output indicator
Digital display
Degree of protection
Pollution degree
Insulation resistance
Dielectric withstand
Vibration resistance
Shock resistance
Ambient illumination
2
Ambient temperature
Ambient humidity
Altitude
Material
Cable length
Weight
Accessory
Applicable standards
1.
to the LAT 61 User's Manual.
2. Variance is ±0.1% F.S. or less depending on the ambient illuminance.
LAT 61 K 30/8 IUPN
30mm
±4mm
Red semiconductor laser class 2 (JIS/IEC/FDA laser notice No. 50)
0.1×0.1mm
0.5μm
NPN open-collector transistor/PNP open-collector transistor (switchable)
Settings for NPN
● Maximum sink current: 50mA
● Applied voltage: 3 to 24V DC (between output and 0V)
● Residual voltage: 2V max. (at sink current of 50mA)
NPN type operation: ON when connecting or connected to 0V (depending on settings)
PNP type operation: ON when connecting or connected to positive terminal of external power supply (depending on settings)
Zero set, reset, memory change, Teaching, Save, or Laser control depending on input time.
PNP type operation: Depending on time to connect positive terminal of external power supply
20MΩ min. at 250V DC megger (between charged parts and casing)
Endurance: 10 to 55Hz (at 1-minute cycle), 1.5mm double-amplitude two hours each in X, Y and Z directions
3,000lx max. (illumination level of light receiving surface under incandescent light)
Approx. 70g (without cable), approx. 320g (including cable), and approx. 380g (with packing)
LAT 61 K 50/20 IUPN LAT 61 K 85/40 IUPN
50mm
±10mm
Max output: 1mW, Emission peak wavelength: 655nm
0.5×1mm
CMOS image sensor
1.5μm
±0.1% F.S.
±0.08% F.S./°C
24V DC ±10% including ripple 0.5V (P-P)
100mA max.
200μs, 500μs, 1ms, 2ms
Output range: 0 to 10.5V (normal), 11V (at alarm)
Output impedance: 100Ω
Output range: 3.2 to 20.8mA (normal), 21.6mA (at alarm)
Load impedance: 300Ω max.
Judgment output or alarm output (switchable)
Settings for PNP
● Maximum source current: 50mA
● Residual voltage: 2.8V max. (at source current of 50mA)
Open when the output is ON.
Incorporated (Auto-reset)
At 0V: NPN open-collector output
At supply voltage of 24V DC: PNP open-collector output
NPN type operation: Depending on time connect 0V
Green LED: ON when laser radiation is being emitted
Yellow LED (No. of indicators: 3): ON during output
Red LED for sign and 5-digit display
IP67 (except connector)
2
1000V AC for 1 min. (between charged parts and casing)
500m/s three times each in X, Y, and Z directions
2
-10°C to 45°C (No dew condensation or icing allowed);
At storage: -20°C to 60°C
35% to 85%RH, At storage: 35% to 85%RH
2000m or less above sea level
Casing: PBT, front cover: acrylic, cable: PVC
5m
Laser warning label: 1 set
Conforming to EMC Directive
4
LAT 61 K 120/120 IUPN
85mm
±20mm
0.75×1.25mm
2.5μm
. For more details on beam dimensions, please refer
di-soric GmbH & C o . KG
Steinbeisstraße 6
DE-73660 Urbach
Fon: +49 (0) 71 81 / 98 79 - 0
Fax: +49 (0) 71 81 / 98 79 - 179
info@di-soric.com
www.di-soric.com
120mm
±60mm
1.0×1.5mm
8μm