G-Clean GC141333 Série Manuel D'utilisation page 14

WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is com-
plete. Failure to comply could result in accidental starting
and possible serious personal injury.
INSTALLING WAND STORAGE BRACKET
See Figure 4.
 Slide the wand storage bracket over the tab on the unit
until it is securely seated.
 Place the trigger handle and the spray wand into the
grooves in the storage bracket when not in use.
INSTALLING G-CLEAN DETERGENT
INjECTOR
See Figure 5.
 Install one side of the garden hose coupler to the water
outlet end of the G-Clean detergent injector.
 Connect the other end of the garden hose coupler to the
water inlet on the pressure washer. Rotate the coupler
clockwise to secure.
NOTE: When connected to the pressure washer, the G-
Clean detergent injector should be positoned sideways
as shown.
 Connect your garden hose to the water inlet end of the
G-Clean detergent injector.
ASSEMBLING SPRAY WAND
See Figure 6.
 Push the end of the spray wand into the trigger handle
and rotate clockwise to secure.
 Pull on the spray wand to be certain it is properly secured.
 Slide the end of the nozzle holder over the bottom of the
trigger handle.
CONNECTING HIGH PRESSURE HOSE TO
PRESSURE WASHER
See Figure 7.
 Remove the protector cap from the high pressure hose
outlet on the pressure washer.
 Press the coupler end of the hose into the high pres-
sure hose oulet on the pressure washer. Lower the hose
coupler over the threaded fitting and turn clockwise to
secure the hose in place.
 Pull on the hose to be certain it is properly secured.
ASSEMBLY
CONNECTING HIGH PRESSURE HOSE TO
TRIGGER HANDLE
See Figure 8.
 Remove the protector cap from the water inlet on the
trigger handle.
 Insert the nut end of the high pressure hose over the
water inlet on the trigger handle and rotate clockwise
to secure. Hand tighten, then use wrench provided to
securely tighten.
 Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE
See Figure 9.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into the
drinking water supply. Direct connection through a
receiver tank or backflow preventer is usually permit-
ted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose:
 Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unrestricted
garden hose between the water intake and the garden
hose faucet or shut off valve (such as a "Y" shut off con-
nector).
 Run water through the garden hose for 30 seconds to
clean any debris from the hose.
 Inspect the screen in the water intake.
NOTE: The detergent injector must be removed to inspect
the filter screen.
 If the screen is damaged, do not use the machine until
the screen has been replaced.
 If the screen is dirty, clean it before connecting the garden
hose to the machine.
 With the hose faucet turned completely off, attach the
end of the garden hose to the water inlet on the detergent
injector. Tighten by hand.
NOTICE:
Do not run the pressure washer pump without water sup-
ply connected and turned on, as this may damage the
high pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Page 10 — English