Noise/Vibration Information; Declaration Of Conformity; Mounting And Operation - Bosch ART 24 Notice Originale

OBJ_BUCH-1983-006.book Page 13 Thursday, September 22, 2016 9:42 AM

Noise/Vibration Information

Sound emission values determined according to
EN 50636-2-91.
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 50636-2-91:
Vibration emission value a
h
Uncertainty K

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with all relevant
provisions of the directives 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC, 2000/14/EC including their amendments and
complies with the following standards: EN 60335-1,
EN 50636-2-91, EN 50581.
2000/14/EC: Guaranteed sound power level:
Conformity assessment procedure according to Annex VI.
Equipment category: 33
Notified body:
TÜV Rheinland Intercert Kft., Budapest, Hungary, Nr. 1008
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017

Mounting and Operation

 Do not disassemble guard once connected.
 Do not connect the machine to the mains socket before
it is completely assembled.
 The cutting line continues to rotate for a few seconds
after the trimmer is switched off. Allow the motor/cut-
ting line to stop rotating before switching "on" again.
 Do not rapidly switch off and on.
 Remove any grass from spool cover when changing line
or spool.
 Only use Bosch approved cutting elements. Cutting
performance will vary with different cutting elements.
Bosch Power Tools
3 600 HA5 8.. 3 600 HA5 2..
3 600 HA5 9.. 3 600 HA5 3..
dB(A) 73
dB(A) 93
dB =1.0 =1.0
2
m/s = 4.5 = 5.0
2
m/s =1.5 =1.5
3 600 HA5 8.. 3 600 HA5 2..
3 600 HA5 9.. 3 600 HA5 3..
dB(A) 94
 Check the guard screw is fixed tightly before using.
 Spool feeds line each time the machine comes to a stop
(trigger is released), and line is cut when machine is
started again.
Action Figure
Delivery Scope 1
Adjusting the Handle 2
Mounting the Cutting Guard 3
Mounting wheels 4
Connecting the extension lead 5
Switching On and Off 6
Working Advice
Adjusting the Cutting Height 7
Changing to edging mode 8
Removing the line spool 9
Winding Line on Spool 10
Replacing the Line Spool 11
Fitting Spool into Spool Holder 12 – 13
Maintenance, Cleaning and Storage 14
Selecting Accessories 15
F 016 L81 619 | (22.9.16)
English | 13
3 600 HA5 4..
3 600 HA5 5..
73 74
93 94
=2.0
= 6.5
=2.0
3 600 HA5 4..
3 600 HA5 5..
94 96
Page
189
189
190
191
191
192
192
192
193
193
194
194
195
195