Caution; Handling Batteries; Unpacking The Appliance; Scope Of Delivery - Clatronic CL 3716 Mode D'emploi

Handling Batteries

WARNING:
• Do not expose batteries to excessive heat such as sunlight, fire or
similar. There is a risk of explosion!
• Batteries are not toys. Keep away from children.
• Do not open batteries by force.
• Avoid contact with metal objects (rings, nails, screws, etc.). There is a
risk of short circuit!
• A short circuit could cause the battery to heat up excessively or even
to catch fire, resulting in injuries.
• For your own safety, cover the battery terminals with adhesive tape
during transport.
• In case of battery leakage, make sure not to rub the liquid into your
eyes or mucous membranes. In case of contact, wash your hands
and rinse your eyes with clear water. Seek medical attention if any
discomfort persists.

CAUTION:

• When not using the remote control for a long period of time, remove
the batteries in order to prevent "leakage" of battery acid.
• Different battery types or new and used batteries must not be used
together.
• Do not dispose of batteries along with domestic waste. Return used
batteries to the relevant collection facilities or your retailer.

Unpacking the Appliance

1. Remove the appliance from its packaging.
2. Remove all the packaging material such as plastic bags, filler material,
cable ties and cardboard packaging.
3. Check that all parts are supplied in the package.
Overview of the Components
1 Lever
2 Air outlet (fins)
3 IR receiver for remote control
4 Control panel
5 Display
6 Handle
7 Grille with internal filter
8 Exhaust pipe connector
9 Water outlet
10 Winding device for power cord
11 Power plug bracket
12 Water outlet

Scope of Delivery

1 Air conditioning appliance

1 Remote control

2 Batteries
1 Flexible exhaust pipe
1 Exhaust pipe adapter (Connection on the appliance)
1 Window kit, 2-piece
1 Adapter for the window exhaust kit
1 Water hose
2 Plugs (spares)
CL3716_IM_new

Notes for Use

CAUTION: Important for initial operation or after transport!
Before initial operation, the appliance must stay in an upright position for
at least 3 hours in order for the cooling agent to sink. The compressor
will be damaged otherwise.
CAUTION:
• When you interrupt the operation with the
3 minutes before switching the appliance on again.
• If you want to move the appliance to another location, first empty the
water tank!
• The appliance operates most effectively with a room size up to 70 m³.
• The flexible exhaust hose and the adapter have been manufactured
especially for this appliance. In order to avoid incorrect operation, do
not replace the pipe with another pipe.
• The exhaust pipe can be extended up to 150 cm. Do not use any
extension.
• Ensure free airflow. Make sure not to kink or bend the exhaust pipe.
Any blockage can cause the appliance to overheat.
• Close all windows and doors in order to prevent outside air from
entering the room and thus allowing a more effective operation of the
appliance.

Putting into Service

Location

• When installing the appliance, make sure to keep a distance of at least
50 cm between the appliance and any walls or other objects.
• The surface must be flat and dry.

Assembly of Exhaust Pipe

NOTE:
For sliding windows, you may use the window kit provided and install it
in a vertical or horizontal position. Adjust the length of the seal plate as
desired.
1. Connect the adapter to the exhaust hose. Place the exhaust hose in a
way that the first fin of the hose lays in the rail. Tighten the adapter by
turning it clockwise.
2. Connect the adapter to the connector on the back of the appliance. To
do this, push the adapter with the narrower side from the right into the
guides. It must audibly snap.
3. Extend the pipe to the desired length.
4. Stick the open end of the pipe into a window.
5. Close the window as far as possible. Also lower any external roller
blinds, if present, to the end of the pipe.
Remote Control
1. Open the battery compartment cover on the back of the remote control.
2. Insert 2 batteries of type R03 "AAA" 1.5 V, observing the correct polarity
(see markings on the bottom of the compartment)!
3. Close the battery compartment cover.

Power Cord

Unwind the power cord from the winding appliance.

Electric Connection

1. Make sure the mains voltage you want to use corresponds to the
voltage of the appliance. Please check the rating label for detailed
specifications.
2. Connect the appliance to a properly installed grounded socket. A signal
will sound indicating that the appliance is ready for use.
button, wait for at least
37
13.12.2018