BSVILLAGE 3EXB0195-FRAME Notice De Montage page 3

3.0
1
CONDITIONS OF POOL INSTALLATION
Fig 4
(g) Make sure the drain plug of the pool is closed and start filling the pool with water. After filling app. 3cm stop the water and smooth all creases on the pool bottom. You can perform it by pressing from
the centre to the edge, where the wall meets the bottom of the pool; or by grasping it from outside where the wall meets the bottom and pulling outward. Then the pool will fill uniformly and it will
maintain its shape. In case of any problems with the shape of the bottom, have two persons pull against each other to remove all creases.
Note: If, after the start of filling, at some places water level reaches 3-5cm higher than in the centre, the pool is not levelled and you need to drain it, level the area or select another one and start over.
Do not move the pool without draining the water, the weight of the water will not allow you to straighten the bottom or to modify the position of the pool without damaging it.
(h) If no filtration unit is connected to the pool, close the connection holes from the inside using the supplied caps. If it is connected, stop filling the pool and assemble and connect the filtration unit to
the pool. See the separate manual for the use and installation of the filtration unit.
(i) Continue filling the pool. The pool walls rise with the water level. During filling, regularly check the pool to make sure it is filling uniformly. Continue filling the water until the level reaches the mark
on the inner wall of the pool and the pool foil is smooth and firm. Do not overfill the pool above this mark.
4.0
INSTRUCTIONS FOR POOL MAINTENANCE
Failure to observe the below given instruction for maintenance may lead to a risk for your health, and health of your children especially.
NOTE: The filtration unit is used for water circulation and to trap small mechanical impurities in the water. The maintenance of cleanliness and hygienic suitability of water in the pool requires mechanical
and chemical maintenance of the water. Correct maintenance will help to maximize the life of your pool.
If you want the water in your pool to be clean and safe for swimming:
(a) Contact your pool and accessories dealer and ask for advice on correct maintenance of pool water cleanliness and safety. One of the most important factors of extension of the filtration insert is the
maintenance of water cleanliness. During maintenance, follow the instructions of your dealer.
(b) Place a shallow wading pool with water next to the pool, so the swimmers may clean their feet prior to entering the pool.
(c) Cover the pool with a cover or solar tarpaulin when not in use. This will reduce the loading of the pool by debris from the environment.
(d) Keep the pool clean. Clean the debris sediment using a soft cloth. Never ruse any concentrated cleaners, abrasive preparations or solvents.
(e) Clean the bottom of the pool regularly from debris sediment.
(f) Replace the filtration insert in the filtration unit every 2 weeks. At the same time use a clean cloth to remove the sediment from the inner walls of the filtration unit.
(g) Use chemicals intended for pools. We recommend the use of a purpose-designed float to apply chlorine preparations in the form of tablets. Follow the instruction on the packaging of individual
preparations. Avoid contact of chemical preparations with the pool wall, until they are dissolved in the pool water. First, dissolve the preparations completely in a smaller amount of water (e.g. in
a bucket) and only then carefully apply it into the pool to avoid contact with it. Never mix chemical preparations together - unexpected reaction may occur. Apply it into the pool gradually and
individually. Do not apply chemical preparations if the pool is in use. It may cause irritation of the eyes, skin or other problems.
ATTENTION: Heavy rain may cause the collapse of the pool. Before heavy rains, preventively lower the water level in the pool and regularly lower it, until the rain passes.
5.0
DISASSEMBLY AND STORAGE INSTRUCTION
IMPORTANT: If you expect the temperature to drop below 5°C, the pool must be placed in storage.
(a) All parts should be cleaned using soap and tepid water. DO NOT USE any solvents or hot water.
(b) Before storage, make sure all parts are dry. It prevents the growth of mould in the folds of the foil.
(c) Store all parts in a dry, heated place, in which the temperature doesn't drop below 4°C, or doesn't exceed 50°C. Failure to observe these storage instructions may cause a damage of the pool and is
a reason for guarantee cancellation.
(d) Follow the above given installation instruction to allow the installation in the next season. Check and level the place of the pool prior to the next installation.
(e) If you want to drain the pool, find the drain hole on the outside wall of the pool and remove the draining cap. Connect a garden hose and lead it to a place, into which you want to drain the water.
After placing the hose in the required place, you can open the cap on the inside of the pool.
(f) After the water level drops sufficiently, remove the filtration unit parts from the pool and drain all water from it.
(g) When the water is drained from the pool, wash the pool with tepid water with soap and then wipe it dry with soft cotton cloth. Place the cap back into the draining hole and attach the drain cap.
(h) On a pool with fixed frame remove the bearing frame. First detach the vertical girders from the T-couplings (by releasing flexible locks), then remove the pins and detach the horizontal braces from
the T-couplings. Clean and dry all parts.
(i) The accessories, such as solar tarpaulins, cover tarpaulins, steps etc., have to be cleaned and dried prior to storage.
(j) Never leave empty surface pool outside.
(k) Protect the pool, filtration unit and other accessories from frost. The guarantee dos not cover the damage by frost.
THE BOTTOM MUST BE FREE OF CREASES AND FOLDS
AND SMOOTH ALL THE WAY TO THE VERTICAL BRACES
VERTICAL
BRACE
Pin
T-coupling
FLEXIBLE
LOCK
VERTICAL
BRACE
FOOT
Foot
EN
Sealing ring