Installation Requirements - MediaShop AQUADON SMART HEATER Mode D'emploi

Installation requirements:

a. Before installation, it must be checked whether
the technical requirements according to the
given technical data are met at the location.
b. Make sure that the device is safely earthed with a
safety socket.
Installation of the outlet pipe (ill. 1)
a. Press the spout or hose (A) to the collar (C) on
the round hole at the top of the main unit (2).
b. Screw the cover (B) to the main unit (2)
NOTE: Take care not to damage the rubber seals (D)
during installation.
INSTALLATION OF THE CONTINUOUS FLOW
HEATER ON THE SINK (ill. 2).
ATTENTION: Your Aquadon is only intended for
connecting the cold water pipe. Please do not
connect the hose to an existing hot water pipe.
If you have both a cold water and a hot water
connection on your wall, only the cold water
connection may be used!
1. With power connection above the sink (ill. 3)
a. Place the spacer ring (8) with the crown facing
upwards into the lower part of the main unit (2).
Make sure that the cable is placed in the recess
provided.
b. Place the rubber sealing ring (3) underneath
the spacer ring (8). Thread the thread of the
continuous flow heater into the hole of the rubber
sealing ring (3).
c. Insert the thread of the continuous flow heater
through the opening provided on the sink or
worktop (4).
d. Insert the cable guide ring (5) from below onto
the thread of the main unit (2), and screw the
fixing nut (6) to fix it in place.
e. Screw the flexible hose to the thread of the
continuous flow heater and to the water outlet on
the wall.
f. Open the water supply, set the continuous flow
heater lever to water flow, and turn the spout/
hose left and right. Make sure the connection is
tight, and fix any leaks before use.
g. Connect the water heater plug to the power supply.
2. With power connection below the sink
(ill. 4). Important! Please ensure that the
opening in the worktop or sink is large
enough for the plug.
a. Place the spacer ring (8) with the crown facing
upwards into the lower part of the main unit (2).
Make sure that the cable is placed in the recess
provided.
b. Place the rubber sealing ring (3) underneath the
M20411_Aquadon_Manual_20190408_MM.indd 8
spacer ring (8). Thread the power cable and the
thread of the continuous flow heater into the hole
of the rubber sealing ring (3).
c. Insert the thread of the continuous flow heater
and the power cable through the opening
provided on the sink or worktop (4).
d. From below, place the cable guide ring (5) (with the
cable recess facing upwards) onto the thread of the
main unit (2). To fix, screw in the fastening nut (6).
e. Screw the flexible hose to the thread of the
continuous flow heater and to the water outlet on
the wall.
f. Open the water supply, set the continuous flow
heater lever to water flow, and turn the spout/
hose left and right. Make sure the connection is
tight, and fix any leaks before use.
g. Connect the water heater plug to the power supply.
NOTE: First connect the water. If all seals are tight,
the device can be connected to the power.
Setting the water temperature (ill. 5):
Depending on the position of the lever, you can
choose between ‚cold', ‚warm' and ‚off' ranges. If
the lever is turned down, the flow for cold water will
increase; turn the lever upwards and the flow for hot
water increases. With an increase in the flow rate in
the warm water range, the water temperature drops. If
the device is operated in the hot water range, you will
see the current water temperature on the display.
NOTE: To conserve power, there is a regulator in the
unit that ensures that electricity is only consumed
during the use of hot water. Connecting and
disconnecting the device is therefore not necessary.
CLEANING AND MAINTENANCE
Cleaning the water outlet (ill.6):
When water flow becomes less consistent or weaker,
the water outlet needs cleaning. Proceed as follows:
Unscrew the water outlet in an anti-clockwise
direction and descale or replace as necessary. Then
reattach the water outlet.
Cleaning of water filter (ill. 7):
If cleaning the water outlet does not produce the
desired effect, remove the water filter at the water
inlet, situated at the bottom of the thread from the
main unit (2), clean it, and then reinstall it.
SPECIFICATIONS:
Power (kw): 3
Water pressure (Mpa): 0,04 – 0,6
Waterproofing Grade: IPX4
Rated voltage: 220 – 240V ~ 50/60 Hz
8
09.08.19 10:21