Safety Devices - Einhell Royal MSB 28 Mode D'emploi

Anleitung MSB 28 SPK1 14.10.2005
GB
4. DO NOT TOUCH or let your hands or body come
in contact with the muffler. Hold unit with thumbs
and fingers encircling the handles.
5. D O N O T O P E R A T E U N I T I N A W K W A R D
POSITIONS, off balance, outstretched arms, or
one-handed. Always use two hands when
operating unit with thumbs and fingers encircling
the handles.
6. DO NOT RAISE STRINGHEAD above ground
level while unit is operating. Injury to operator
could result.
7. DO NOT USE UNIT FOR ANY PURPOSES
OTHER than trimming lawn or garden areas.
8. DO NOT OPERATE UNIT FOR PROLONGED
PERIODS. Rest periodically.
9. DO NOT OPERATE UNIT WHILE UNDER THE
INFLUENCE OF ALCOHOL OR DRUGS.
10. DO NOT OPERATE UNIT UNLESS DEBRIS
SHIELD AND/OR GUARD IS INSTALLED AND
IN GOOD CONDITION.
11. DO NOT ADD, REMOVE OR ALTER ANY
COMPONENTS OF THIS PRODUCT. Doing so
could cause personal injury and/or damage the
unit voiding the manufacturer's warranty.
12. DO NOT operate your unit near or around
flammable liquids or gases whether in or out of
doors. An explosion and/or fire may result.
13. DO NOT USE ANY OTHER CUTTING TOOLS.
For your own safety only use the accessories
and additional equipment specified in the
operating manual or recommended or specified
by the manufacturer. The use of tools or
accessories other than those recommended in
the operating manual or catalog may place you in
danger of personal injury.
2. Layout and items supplied (Fig. A, B
and C)
A/1, B/1 Cutting head
A/2 Cutting line
A/3, B/3 Outer guard hood
A/4, B/4 Cutting blade
A/5, B/5 Inner guard hood
A/6, B/6 Long handle with drive shaft
A/7, B/7 "Bike" handle
A/8 Throttle lever in the right-hand handle
A/9 Engine switch "off" and "on"
A/10 Throttle lever "lock"
A/11 Throttle lever "release"
A/12 Levers for "Choke" - "Half throttle" - "Full
throttle"
A/13 Housing for engine cooling and starter
A/14 Petrol tank
20
13:04 Uhr Seite 20
A/15 Air filter cover
A/16 Handle for cable pull start
A/17 Petrol accumulation button
A/18,B/18 Carrying strap
A/19 Retainer screw for long handle with drive
shaft
B 20 Tool for cutting head and cutting wire
C/21 3 M5 screws for inner guard hood
C/22 3 M6 screws for outer guard hood
C/23 Spacer sleeve
C/24 Carrier plate for cutting head or cutting
blade
C/25 Pressure plate for cutting blade assembly
C/26 Fastening nut for cutting blade
C/27 2xCable tie
C/28 Safety split pin
C/29 Retainer pin for carrier plate
C/30 Key for spark plug and fastening nut

SAFETY DEVICES

It is imperative that the GUARD HOOD is assembled
in order to prevent injuries to the operator due to
objects catapulted by the machine. In addition, the
integrated blade in the guard hood automatically cuts
the cutting line to the optimum length.
3. Proper operation
The petrol power scythe is intended for private use,
i.e. for use in home and gardening environments.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the petrol power scythe is properly used
and maintained. The instructions contain valuable
information on operating, maintenance and servicing
conditions.
Important! Due to the high risk of bodily injury to the
user, the petrol power scythe must not be used to
carry out the following work: to clean (suck up) dirt
and debris off walkways, or to chop up tree or hedge
clippings. Moreover, the petrol power scythe may not
be used to level out high areas such as molehills.
For safety reasons, the petrol power scythe may not
be used as a drive unit for other work tools or toolkits
of any kind.
4. Assembling the components
Some parts of the power scythe come disassembled.
For quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional tools
(not supplied) for assembly, and also for
maintenance work:
a screwdriver
an Allen key