Hitachi Koki SV 8SA Mode D'emploi page 5

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
English
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-load speed
Sanding pad size
Sanding paper size
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
Sanding paper (Grain: AA 100) ............................... 1
Dust bag ..................................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
<For SV8SA use>
80 × 170 mm paper clip type sanding paper
Grain: AA60, AA100, AA150
80 × 130 mm Velcro type sanding paper
Grain: AA60, AA100, AA150
<For SV12SF use>
114 × 140 mm paper clip type sanding paper
Grain: AA60, AA100, AA150
110 × 100 mm Velcro type sanding paper
Grain: AA60, AA100, AA150
110 × 100 mm stick-on type sanding paper
Grain: AA60, AA80, AA100, AA120, AA150, AA180
Outer diameter 125 mm stick-on type sanding paper
Grain: AA60
2. Sanding pad
<For SV8SA use>
80 × 130 mm sponge pad (Velcro type)
<For SV12SF use>
110 × 100 mm sponge pad (Velcro type)
110 × 100 mm stick-on pad
Outer diameter 125 mm stick-on pad
3. Dust collector (Model WDE-1200)
4. Punch plate
Optional accessories are subject to change without notice.
APPLICATIONS
Finish polishing of woodwork surfaces
Sanding surfaces of woodwork or sheet metal prior
to painting, etc.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
4
SV8SA
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
200W*
14000/min.
80 mm × 130 mm
80 mm × 170 mm
1.1 kg
2. Power switch
Ensure that the power switch is in the OFF positon.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Installing the sanding paper
(1) Bending the sanding paper:
Position the sander with its pad side facing upward
as shown in Fig. 1. Place the sanding paper on the
pad so that the center of the sanding paper is
aligned with the center of the pad, and bend both
ends of the sanding paper at a 90° angle. Then,
bend both ends again in the manner shown in Fig.
2. The sanding paper is now ready to be installed
on the sander.
(2) Installing the sanding paper:
While ensuring that the cord is not bent, place the
sander on a workbench as shown in Fig. 3, and
insert one end of the sanding paper (bent section).
Next, insert the remaining bent section in the same
manner.
CAUTION
The sanding paper must be precisely installed on
the pad, ensuring that there is ample tension (leaving
no slack). Loosely installed sanding paper could
result in unevenly sanded surfaces and/or damage
to the sanding paper itself.
5. Attaching and Removing the Dust Bag
(1) Attaching the Dust Bag
As shown in Fig. 4, hold the dust gate and push
it in the direction of Arrow A to attach it to the
dust outlet.
(2) Removing the Dust Bag
As shown in Fig. 4, hold the dust gate and pull it
in the direction of Arrow B to remove it from the
dust outlet.
PRACTICAL OPERATING PROCEDURES
CAUTION
Never apply water or grinding fluid when sanding.
This could result in electrical shock.
SV12SF
110 mm × 100 mm
114 mm × 140 mm

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Sv 12sf

Table des Matières