Product Description And Specifications - Bosch GSC 12V-13 Professional Notice Originale

Only carry out work with a fitted chip deflector. Make
u
sure that the chip deflector is not damaged or bent out
of shape. Working without a chip deflector or with a dam-
aged chip deflector poses a risk of injury. Have a dam-
aged chip deflector replaced immediately by an author-
ised after-sales service centre for Bosch power tools.
Wear protective gloves during work. Make sure that
u
cut sheet parts are not bent towards your body. Sharp
burrs develop on cut sheets; these can cause injury.
When necessary and while wearing gloves, press bending
sheet parts away from your body.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metals without
incurring any loss from chipping. It is suitable for straight
and curved cuts.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Battery release button
(2) Battery
(3) Button for battery charge indicator
(4) Battery charge indicator
(5) On/off switch
(6) Chip deflector
Bosch Power Tools
(7) Handle (insulated gripping surface)
(8) Fastening screw for top cutter
(9) Top cutter
(10) Bottom cutter
(11) Set screw for top cutter
(12) Fastening screw for bottom cutter
A)
(13) Setting gauge
(14) Hex key
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless metal shears
Article number
Rated voltage
No-load stroke rate n
0
Max. steel sheet cutting ca-
A)
pacity
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Recommended batteries
Recommended chargers
A) Refers to steel sheets of up to 400 N/mm
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
2 2
a = 7 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
English | 11
GSC 12V-13
3 601 J26 1..
V= 12
-1
min 3600
mm 1.3
mm 15
B)
kg 1.4–1.6
°C 0 to +35
°C −20 to +50
GBA 12V...
GAL 12...
GAX 18...
2
1 609 92A 509 | (02.12.2019)