Washer Diagnostic Mode - Maytag MAH22PDAGW0 Instructions D'installation

CODE EXPLANATION
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
"ADD" or "AVAILABLE" rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected "OFF."
PS Selected "ON." Press the DELICATES & KNITS key
pad once for this selection.
Press the WOOLENS key pad once to advance
to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
n. 00 Not Selected "OFF."
n. CE Selected "ON." Press the DELICATES & KNITS key
pad once for this selection.
Press the WOOLENS key pad once to advance
to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the PERMANENT PRESS key pad.
Factory pre-set for 800 rpm.
Press the WOOLENS key pad once to advance
to next code.
U. 00 PENNY INCREMENT OFFSET
U. 00 This option is not supported for European Models
and the value must be set to 00.
Press the WOOLENS key pad once to advance
to next code.
A1. 00 PREWASH LENGTH
A1. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select between
2 and 7 minutes by pressing the PERMANENT
PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high speed
spin. Choose from 3-8 minutes by pressing the
PERMANENT PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number of
cycles in HUNDREDS.
2 00 Represents the number of
cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the WOOLENS key pad once to advance to
next code.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225 cycles
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 00 Number of coins in
HUNDREDS
4 00 Number of coins in ONES
5 00 Number of COINS.
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
■
PD Models: Reinstall access door.
■ PN Models:
Unplug washer or disconnect power.
Open console, reinsert plug into AA1, close console.
Plug in washer or reconnect power.
■ PN MODELS WITH PROGRAMMING SWITCH:
Turn key clockwise and remove.
■ PN MODELS WITHOUT PROGRAMMING SWITCH:
Set-up mode can be exited by using procedures from.

Washer Diagnostic Mode

To enter the "Washer Diagnostic Mode," first enter "Start
Operating Set-up." Then press and hold the DELICATES AND
KNITS key pad for 1 second while in any of the set-up codes one
through six, anytime a diagnostic code is present, or while dAS
displays if operating with Maytag Data Acquisition set-up.
On entry to diagnostic mode the entire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diagnostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options
are permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. Washer Cleanout cycle - With the entire display flashing, this
cycle is started by pressing the BRIGHT key pad.
Use the Washer Cleanout cycle once a month to keep the
inside of your washer fresh and clean. This cycle uses a
higher water level. Use with liquid chlorine bleach to
thoroughly clean the inside of the washer. This cycle should
not be interrupted.
IMPORTANT: Do not place garments or other items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
2. Cycle Credit - With the entire display flashing, a cycle may be
credited by pressing the PERMANENT PRESS key pad (CC
will display). When the service mode is exited, "SELECT
CYCLE" will be displayed unless the end-of-cycle door
opening is required.
3. Manual Overview Test - With the entire display flashing, this
cycle is started by pressing the WHITES key pad. This cycle
provides more typical full length fills, tumbles, drains, and
actuator dispenser movement, allowing for a more thorough
analysis of the washer operation, including pressure switch
behavior.
4. Quick Spin Cycle - With the entire display flashing, this cycle
is started by pressing the COLORS key pad. This cycle
provides a method to quickly drain and spin (remove water
from the washer) if desired.
3 01 = 400 x coin 1
4 68 = 272 x coin 1
5 75 = 3 x coin 1
Total = 675 x coin 1
13