Use; Weighing Function; Saving Personal Data; Measurement And Analysis - ProfiCare PC-PW 3008 BT Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18

Use

NOTE:
• The buttons are sensor touch buttons. Touch the but-
tons lightly with a finger to execute the function.
• The scales are factory set with the units "kg" and "cm".
To change the settings to "lb" or "st:lb" as well as "ft:in",
proceed as follows:
1. Turn on the scales by light pressure with the foot onto the
weighing surface.
2. Press the
or
button repeatedly until the desired
weight unit is displayed. The unit for the height also auto-
matically changes.

Weighing Function

1. Place the scale on a hard, flat surface (avoid carpets). An
uneven floor contributes to inaccurate measurements.
2. Stand on the scales with both feet. The appliance
switches on automatically.
3. Distribute your weight equally and wait for the scale to
determine your weight.
4. The digits on the display will flash before your exact
weight will be shown.
• In order to extend the battery life, the appliance will
automatically turn off 15 seconds after you have stepped
off the scale.
• If there is no weight determination while "0.0" is shown,
the scale will shut off automatically after 15 seconds.

Saving Personal Data

NOTE:
• The scale has default values that you can change, as
described below.
• Carry out the following steps in sequence and within a
few seconds. Otherwise, the appliance will automati-
cally cancel input mode.
• Holding one of the buttons ( / ) pressed for approx.
2 seconds selects fast mode.
1. Press the button . The memory location selected last
flashes on the display (for example P0). Confirm the
setting by pressing
or select another memory space
by pressing the / button. Then press
next setting.
2. The symbol for "male" or "female" will flash. Confirm the
setting by pressing
or use the / button to choose
the symbol for your gender. Then press
next setting.
3. The height setting will flash. Select your height by press-
ing
or
button. Confirm your entry by pressing .
4. The setting age will flash. Select your age by pressing
or
button. Confirm your entry by pressing .
42
PC-PW3008 BT_IM
5. The short display "
for this memory location. Then you will see the memory
location, the symbol of the gender and the weight "0.0 kg"
(0.0 lb / 0: 00 st:lb) in the display.
You now have the following options:
• Press the
again or to change them.
• You can set further preset locations. Proceed as de-
scribed above.
• You can immediately start measuring.

Measurement and Analysis

Record your personal data in the memory.
NOTE:
• The analysis scale will only work correctly when you
are standing on the contact surfaces barefoot and with
slightly moistened foot soles, if possible. Completely
dry foot soles can lead to unsatisfactory results as they
have a conductivity that is too low.
• If necessary wipe the contact surfaces to improve
results.
• Due to the significant fluctuation of body fat, it is difficult
to attain a standard value. Therefore, to obtain consist-
ent data, always measure at the same time of day.
• Amongst other things, our body consists of body
fat, body water, muscle mass and bone weight. The
obtained values may differ due to individual water reten-
tion within these main components. This is normal and
highly dependent on nutrition and lifestyle.
1. Press the
stored position at which your data is saved. The location
flashes for approx. 3 seconds. Then you will see the
memory location, the symbol of the gender and the weight
"0.0 kg" (0.0 lb / 0: 00 st:lb) in the display.
2. Stand on the contact surfaces (5) of the scales with both
feet.
3. Firstly your weight will flash on the display. The analysis
starts after the display has stopped flashing. You'll see
a treadmill "
Remain on the scales until the last display (body age)
has appeared.
to go to the
The following results are displayed one after the other:
1. The weight in the previously selected unit (kg / lb / st:lb)
2. The body fat proportion in % (fat)
3. The proportion of body fluid % (TBW)
to go to the
4. The proportion of muscle mass in % ( )
5. The bone weight in kg (
6. The basal metabolic rate of the daily energy requirement
in KCAL
7. The Body Mass Index (BMI)
8. The visceral fat (
9. The biological age (body age)
" will terminate the entry mode
button repeatedly to display the settings
button. Use the / button to select the
" in the display during the analysis.
)
)
28.09.17

Publicité

Table des Matières
loading

Table des Matières