Black & Decker ASI500 Mode D'emploi page 9

Switch the main power switch(1) to the pump

position (a, fig. E).
Remove the high-volume hose (7) from the storage

channel around the centre of the unit and connect it to
the high-volume pump inflate connection (10) (fig. F).
Insert the hose (with accessories if required) to the item

to be inflated.
To start the pump press the power switch (22) on the

LCD.
When the item is inflated as required or to stop the pump

at any time press the power switch (22) on the LCD.
Remove the hose from the item and store it on the unit.

Turn the main power switch (1) to the off

position (b fig. E).
To deflate using the high-volume pump (i.e air mattresses,
rafts, swimming pool floats):
Note: The pump mode DOES NOT have an auto shut-off
feature.
Switch the main power switch (1) to the pump

position (a fig. E).
Remove the high-volume hose (7) from the storage

channel around the centre of the unit and connect it
to the high-volume pump deflate connection (4) (fig. F).
Insert the hose (with accessories if required) into the

item to be deflated.
To start the pump press the power switch (22) on

the LCD.
When the item is deflated or to stop the pump at any

time press the power switch (22) on the LCD.
Remove the high-volume hose ((7) from the item and

store it in the storage channel around the centre of
the unit.
Turn the main power switch (1) to the off

position (b fig. E).
Operating the LED light
To switch on the LED light (12):
Switch the main power switch (1) to the inflate (c fig. E)

or the pump (a fig. E) position.
Press either of the - or + buttons (21, 23) on the LCD (2)

to turn the LED light (12) on.
To switch the LED light (12) off:
Press either of the - or + buttons (21, 23) again.

Turn the main power (1) switch to off.

Sleep mode to preserve battery life
The unit is fitted with a sleep mode function that will help
prolong the life of the internal battery.
If the unit is left on and unused for more than two minutes the
unit will switch into sleep mode.
To power the unit again either switch the main power

switch (1) on and off or press any button on the LCD (2).
Note: After sleep mode, all settings will be lost and will need
to be re-entered following the instructions under the heading
'Setting the automatic shut-off pressure (fig. E)'.
Maintenance
Your Black & Decker corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper appliance/tool care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless appliance/tool:
Switch off an unplug the appliance/tool.

Or switch off and remove the battery form the appliance/

tool if the appliance/tool has a separate battery pack.
Unplug the charger before cleaning it. Your charger

does not require any maintenance apart from regular
cleaning.
Regularly clean the ventilation slots in your appliance/

tool/charger using a soft brush or dry cloth.
Regularly clean the housing using a damp cloth. Do not

use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust

from the interior (when fitted).
Troubleshooting
Problem Possible cause
Inflator will not Internal battery
operate. fault.
12 Vdc adapter not
connected.
Accessory socket
not live.
Main ON/OFF
switch not in
correct position.
The fuse in the
12 Vdc adapter is
blown.
Cord or switch is
damaged.
Will not inflate. Incorrect mode
selected.
ENGLISH
Possible solution
Recharge the
battery.
Connect the 12 Vdc
adapter.
Turn key to
accessory position
Turn main switch to
required position.
Replace the fuse with
one of the same size
and type (8A/250V).
Have the cord or
switch replaced at a
Black & Decker
Service Centre or
Authorised Service
Centre.
Select correct mode.
9