Assembly And Use Of The Pitcher - Ninja Auto-iQ BL689C Série Guide D'utilisation

ASSEMBLY AND USE OF THE PITCHER

Fig. 3a
OR
Fig. 1
AUTO
Fig. 2 Fig. 3b FROZEN DRINKS
SMOOTHIES
AUTO PUREE
LOW
MED
1 Review warning and Important
Safety Instructions on pages 3–4
before proceeding step 2.
2 Place the motor base on a clean, dry,
level surface such as a counter or
tabletop. Press down on the motor
base to make sure the suction cups
AUTO
adhere to the surface.
AUTO
3 Align and lower the pitcher onto the
motor base (Fig. 1). Handle should
be aligned slightly to the right of
the LOCK symbol ( ) on the motor
base.
4 Rotate the pitcher clockwise until
it clicks in place. As the pitcher
rotates, it will lower and the safety
tabs on the bottom of the pitcher
will slide under the safety tabs on
the top of the motor base (Fig. 2).
5 The pitcher can be placed on the
motor base two ways; the handle
can be on the front right corner or
the front left corner (Fig. 3a, Fig. 3b).
6 Holding the stacked blade assembly
by the top of the shaft, place it onto
the drive gear inside the pitcher.
Ensure that the it is seated properly
and is standing upright (Fig. 4).
NOTE: The Stacked Blade Assembly
will fit loosely on the drive gear.
7
1-877-646-5288
It's best to add liquid ingredients
first and then dry ingredients.
Fig. 4 HIGH PULSE Fig. 5a
LOW DOUGH
SMOOTHIE PUREE FROZEN SERVE SINGLE
BLENDING
HIGH PULSE AUTO
7 Add your ingredients to the pitcher,
making sure they do not exceed the
highest measured marking line on
the side of the pitcher.
NOTE: If you need to add additional
ingredients while the appliance is
processing, open the pour spout cap
FROZEN DRINKS
SMOOTHIES
and pour the ingredients in through
PUREE
LOW MED HIGH PULSE AUTO
the opening.
NOTE: When blending any kind of
liquids, such as mixtures of any drinks
or smoothies, do not exceed the "MAX"
liquid mark (64 oz.) on the pitcher.
8 Plug the power cord into the electrical
outlet and press the power button ( ).
NOTE: As a safety feature, the power
light ( ) will flash and the motor will
not work if the pitcher and lid are not
installed correctly. When the pitcher
and lid are installed properly, the
power light ( ) will be solid, indicating
that the appliance is ready for use.
9 Holding the lid by the handle in the
upright position, place it on top of
the pitcher, aligning the triangle
( ) located on the lid with the
triangle ( ) located on the pitcher's
handle (Fig. 5a). Press the handle
down until you hear a click. The
triangles on the lid and the pitcher
USE
Fig. 5b
Fig. 7
handle MUST be aligned in order for
the blender to turn on (Fig. 5b).
10 Press the power button to turn on
the unit. Select the speed or Auto-iQ®
program that best suits your needs.
The Auto-iQ® program will stop the
appliance automatically at the end
of the program (Fig. 7.)
11 To pause the appliance, press the
selected speed or Auto-iQ® program
a second time. When the program
is paused, the light on the program
button will flash until you press it
again to resume the program.
12 When ingredients have reached
your desired consistency, stop the
appliance by pressing the power
button ( ) and wait for the stacked
blade assembly to stop turning
(Fig. 7).
13 Turn the pitcher counterclockwise,
then lift it off the base. (Fig. 8)
14 Open the pour spout cap and use
the spout to empty liquid contents.
For thicker consistencies, first
remove the lid by pressing the
release button and pulling the lid
handle up to a 90-degree angle to
REMOVAL
Fig. 9
Fig. 10
Fig. 8
lift lid off the pitcher. Then, carefully
remove the stacked blade assembly
by the top of the shaft. Place the
stacked blade assembly away from
the work area to avoid accidental
contact. Finally, empty contents
from the pitcher (Fig. 9).
15 Unplug the unit. To release the motor
base from the counter or tabletop,
place your hands underneath both
sides of the motor base and gently
pull the unit up and toward you
(Fig. 10).
ninjakitchen.com
8