Before First Use; Assembly And Use Of The Pitcher - Ninja BL780C Manuel Du Propriétaire

Before First Use

PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Make sure that the motor base
is plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the Blade Assembly
in first.
IMPORTANT: Blade Assemblies are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
9 1-877-646-5288
WARNING: Stacked Blade
Assembly is sharp and not
locked in place. If using the
pour spout, ensure the lid is
fully locked onto the pitcher.
Failure to do so will result in a
risk of laceration.
WARNING: Stacked
Blade Assembly is sharp
and not locked in place.
If pouring with the lid
removed, carefully remove
the Stacked Blade Assembly
first, holding it by the shaft.
Failure to do so will result in
a risk of laceration.
WARNING: Chopping
Blade Assembly is sharp and
not locked in place. Before
emptying contents carefully
remove lid and Chopping
Blade Assembly, holding it by
the shaft. Failure to do so will result in a
risk of laceration.
CAUTION: Do not immerse the motor base into
water or any other liquid.
1 Remove all packaging material and labels from the
appliance. Separate/remove all parts from each other.
2
Wash the lids, pitcher, bowl, Nutri Ninja ™ cups and
blade assemblies in warm, soapy water. When washing
the blade assemblies, use a dish-washing utensil with a
handle to avoid direct hand contact with blades.
CAUTION: Handle the Blade Assemblies with care
when washing, as the blades are very sharp.
3
Handle blade assemblies with care to avoid contact with
sharp edges. Rinse and air dry thoroughly.
4 The pitcher, bowl, Nutri Ninja cups, lids and blade
assemblies, are all dishwasher safe. It is recommended
that the lids and blade assemblies be placed on the top
rack. Ensure that the blade assemblies are removed
from the containers before placing in the dishwasher.
5 Wipe the motor base clean with a damp cloth.

Assembly and Use of the Pitcher

WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 3a
Fig. 1
Fig. 2 Fig. 3b
1
Review warning and caution statements above before
proceeding to number 2.
2 Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor
base to make sure that the Suction Cups adhere to the
counter or table top.
3 Align and lower the Pitcher onto the motor base.
(Fig. 1) Handle should be aligned slightly to the right of
the "LOCK" symbol on the motor base.
4 Rotate the pitcher clockwise until it locks in place. As
the pitcher rotates, it will lower and the safety tabs on
the bottom of the pitcher will slide under the safety tabs
on the top of the motor base. (Fig. 2)
5
The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
6
Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the Stacked Blade Assembly is seated
properly and is standing upright. (Fig. 4)
NOTE: The Stacked Blade Assembly will fit loosely on
the drive gear.
OR
Fig. 4
Fig. 5
7
Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
"Max liquid" mark (1.9 L) on the pitcher
8 Holding the lid by the handle in the upright position,
place it on top of the pitcher aligning the triangle
( ) located on the lid with the triangle ( ) located
on the pitcher's handle. The triangles on the lid and
the blender handle MUST be aligned in order for the
blender to turn on. (Fig. 5) Press the handle down until
you hear a click.
IMPORTANT: As a safety feature, the power
button ( ) will flash and the motor will not work
if the pitcher and lid are not installed correctly.
When the pitcher and lid are installed properly,
the power button ( ) will be solid, indicating that
the appliance is ready for use.
9 Plug the power cord into the electrical outlet and press
the power button ( ).
www.ninjakitchen.com 10