Preparing The Mower For Long-Term Storage - Einhell Royal BM 51 Instructions De Montage Et Mode D'emploi

Anleitung BM 51 SPK 7 17.01.2006
damaged blade.
Resharpening the blade
The blades can be resharpened with a metal file. In
order to avoid imbalance, the blade should be
resharpened by an authorized service workshop.
4. Checking the oil level
Important: Never run the engine with no or too little
oil. This could cause severe damage to the engine.
Use only 15W40 engine oil.
Checking the oil level:
Stand the lawn mower on a flat level surface.
Unscrew the oil dip stick by turning anticlockwise,
pull out and wipe. Insert the dip stick back in the
filling mount as far as the stop, but do not screw back
in. Pull out the dip stick again and read off the oil
level while holding horizontally. The oil level must be
between the maximum (top edge of the flat-pressed
metal stick, Fig. N) and the minimum (bottom edge of
the flat-pressed metal stick, Fig. N). The moveable
orange plastic part on the oil dip stick provides
protection against oil foam.
Changing the oil:
Stand your lawn mower on a work bench with the
front right-hand wheel (in the pushing direction)
projecting beyond the edge of the work bench. Place
a flat oil pan beneath the lawn mower (Fig. O).
Remove the oil outlet screw on the underside of the
lawn mower (see Fig. P). Completely empty the used
oil. Screw the oil outlet screw back on tightly. Fill with
0.4 liters of fresh 15W40 engine oil (see Checking
the oil level).
5. Care of the tension cables and setting the
tension cable for the engine brake
Oil the tension cables regularly and check that they
move smoothly.
The setting of the engine brake play must be
checked every time before starting the mower:
a) Fasten the lever for the engine brake with
adhesive tape (Fig. G).
b) Check the setting of the play between the
setting screw and the tension cable nipple
(distance approx. 2 - 4mm, Fig. Q+R).
c) If the distance is too small (Fig. Q) it must be
corrected by slackening the setting screw and
readjusting (Fig. R).
6. Maintenance of the air filter
A soiled air filter will reduce the performance of the
engine because it will prevent enough air getting to
13:05 Uhr Seite 21
the carburetor. It is therefore imperative that regular
checks are made. The air filter should be checked
every 25 hours and cleaned if required. If the air is
very dusty the air filter should be checked more
regularly.
Important: Never clean the air filter with petrol or
inflammable cleaning agents (Fig. S). Clean the air
filter with compressed air or simply by knocking out
any soiling.
7. Repairs
After any repair or maintenance work, check that all
safety-related parts are in place and in proper
working order.
All parts which may cause injury must be kept where
they are inaccessible to children or others.
Important: In accordance with product liability
legislation we are not liable for any damages caused
by improper repairs or the use of spare parts that are
not original spare parts or parts approved by us. In
addition, we are also not liable for any damages
arising from improper repairs. Such work should be
performed by a customer services workshop or
authorized specialist. The same applies to accessory
parts.
8. Times of use
Lawn mowers are only permitted to be used on
workdays between the hours of 7.00 a.m. and 7.00
p.m. Please comply with statutory regulations, which
may vary from location to location.
13. Preparing the mower for long-term
storage
Caution: Do not empty the petrol tank in enclosed
areas, near fire or when smoking. Petrol fumes can
cause explosions and fire.
1. Empty the petrol tank with a petrol suction pump.
2. Start the engine and let it run until any remaining
petrol has been used up.
3. Change the oil at the end of every season. To do
so, remove the used engine oil from a warm
engine and refill with fresh oil (see Changing the
oil, item 12/4).
4. Remove the spark plug from the cylinder head.
Fill the cylinder with approx. 20 ml of oil from an
oil can. Slowly pull back the starter handle, which
will bathe the cylinder wall with oil. Screw the
spark plug back in.
5. Clean the cooling fins of the cylinder and the
housing.
6. Be sure to clean the entire machine to protect
the paint.
GB
21