Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Thrust Load Weight
Type
6MFE 55
5000/10000
6MFE 75
5000/10000
6MFE 100
6MFE 125
6MFE 150
6MFE 175
6MFE 200
6MFE 250
6MFE 300
6MFE 400
Thrust Load Weight
Type
6MFE 55
5000/10000
6MFE 75
5000/10000
6MFE 100
6MFE 125
6MFE 150
6MFE 175
6MFE 200
6MFE 250
6MFE 300
6MFE 400
Thrust Load Weight
Type
6MFE 55
5000/10000
6MFE 75
5000/10000
6MFE 100
6MFE 125
6MFE 150
6MFE 175
6MFE 200
6MFE 250
6MFE 300
6MFE 400
Ts=starting torque Tn=rated torque In=rated current S.F.=service factor Istart=locked rotor current
For informations about special voltages, please contact Pentax s.p.a. Tech. Dep.
USE LIMITATIONS
For good operating of the motor, in a 6" well, please check the following conditions:
- Maximun motor immersion depth is 100 meters.
- Maximun allowable starts per hours: 30 for direct starting, 15 for star-delta.
- Maximun well water temperature is 35 °C
- The motor uses the water flow, produced by the pump, to assure a suitable heat exchange
not lower than 0.16 m/sec.
PRECAUTION AND PRELIMINARY CHECKS
During transportation and unpacking, care should be taken to avoid hitting the motor.
Check that the power cable has not been damaged.
Do not use the power cable to make the motor move.
Motor power rating is adeguate for the required application.
Power supply voltage and frequency comply with the specifications given on the motor nameplate.
Do not unscrew the filling plug: there is no need to up the cooling fluid in this type of motor and don't remove
any parts of the motors.
The well, in which the motor will be installed, should be clean.
The installation must be done by skilled operators.
Technical data for 6MFE series Pentax 6" motors
H
N
Kg
mm
32
540
40
570
10000
42
600
10000
45
600
10000
48
700
10000
50
700
10000
54
760
10000
65
830
10000
70
890
20000
90
1030
Technical data for 6MFE series Pentax 6" motors
H
N
Kg
mm
32
540
40
570
10000
42
600
10000
45
600
10000
48
700
10000
50
700
10000
54
760
10000
65
830
10000
70
890
20000
90
1030
Technical data for 6MFE series Pentax 6" motors
H
N
Kg
mm
32
540
40
570
10000
42
600
10000
45
600
10000
48
700
10000
50
700
10000
54
760
10000
65
830
10000
70
890
20000
90
1030
I sf
I sf load
kW
Hp
Amp
Amp
4
5,5
9,6
10,7
5,5
7,5
13,0
15,1
7,5
10
17,4
19,2
9,2
12,5
20,2
22,4
11
15
25,6
29,4
12,8
17,5
27,5
31,1
15
20
34,1
38,0
18,5
25
39,8
45,6
22
30
47,3
54,6
30
40
66,2
75,0
In
Isf load
kW
Hp
Amp
Amp
4
5,5
15,9
16,8
5,5
7,5
23,5
26,2
7,5
10
29,0
32,8
9,2
12,5
35,0
38,8
11
15
39,8
47,2
12,8
17,5
47,0
53,8
15
20
54,5
61,5
18,5
25
67,5
76,0
22
30
80,2
91,0
30
40
In
Isf load
kW
Hp
Amp
Amp
4
5,5
7,8
8,9
5,5
7,5
11,0
12,6
7,5
10
14,9
16,8
9,2
12,5
19,8
22,4
11
15
21,0
24,0
12,8
17,5
25,1
28,2
15
20
27,2
30,6
18,5
25
33,8
38,0
22
30
40,2
45,5
61,8
30
40
53,0
-
60 Hz
-
RPM Cosj EFF% Ts/Tn
3440
0,86
74
2,4
3450
0,82
79
2,4
3440
0,82
80
2,3
3450
0,84
81
2,3
3460
0,81
82
2,1
3450
0,85
82
2,1
3450
0,81
83
2,1
3460
0,83
84
2,1
3450
0,83
85
2,1
3450
0,81
85
2,0
-
60 Hz
-
RPM
EFF% Ts/Tn
Cosj
3440
0,83
74
2,4
3450
0,82
72
2,4
3440
0,81
80
2,3
3450
0,82
80
2,3
3440
0,85
82
2,1
3450
0,83
82
2,1
3450
0,85
82
2,1
3460
0,82
84
2,1
3450
0,82
85
2,1
-
60 Hz
-
RPM
Cosj
EFF% Ts/Tn
3440
0,85
76
2,4
3450
0,82
78
2,4
3440
0,82
77
2,3
3440
0,81
78
2,3
2,1
3440
0,81
80
3440
0,86
81
2,1
3450
0,84
81
2,1
3440
0,84
82
2,1
3440
0,83
83
2,1
3450
0,84
85
2,0
S.F.
1,15
S.F.
1,15
S.F.
1,15
Publicité
Table des Matières
