Maintenance And Service; Maintenance And Cleaning - Bosch GWS 8-115 Professional Notice Originale

Masquer les pouces Voir aussi pour GWS 8-115 Professional:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 25
OBJ_BUCH-340-005.book Page 25 Friday, May 13, 2011 8:08 AM
Cutting Metal
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
When cutting, work with moderate feed, adapted to the mate-
rial being cut. Do not exert pressure onto the cutting disc, tilt
or oscillate the machine.
Do not reduce the speed of running down cutting discs by ap-
plying sideward pressure.
When cutting profiles and square bar, it is best to start at the
smallest cross section.
Cutting Stone
Provide for sufficient dust extraction when cutting
stone.
Wear a dust respirator.
The machine may be used only for dry cutting/grinding.
For cutting stone, it is best to use a diamond cutting disc.
When using the cutting guide with dust extraction protection
guard 21, the vacuum cleaner must be approved for vacuum-
ing masonry dust. Suitable vacuum cleaners are available
from Bosch.
For cutting expecially hard material, e. g., concrete with high
pebble content, the diamond cutting disc can overheat and
become damaged as a result. This is clearly indicated by cir-
cular sparking, rotating with the diamond cutting disc.
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short
time at maximum speed with no load.
Bosch Power Tools
Noticeable decreasing work progress and circular sparking
are indications of a diamond cutting disc that has become
dull. Briefly cutting into abrasive material (e. g. lime-sand
brick) can resharpen the disc again.
Information on Structures
Slots in structural walls are subject to the Standard DIN 1053
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural
The machine must al-
engineer, architect or the construction supervisor.
ways work in an up-
grinding motion. Other-

Maintenance and Service

wise, the danger exists
of it being pushed un-
controlled out of the

Maintenance and Cleaning

cut.
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a residual current device (RCD). When work-
ing metals, conductive dust can settle in the interior of the
power tool. The total insulation of the power tool can be im-
paired.
Please store and handle the accessory(-ies) carefully.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
Switch on the machine
ing maintenance and repair of your product as well as spare
and place the front part
parts. Exploded views and information on spare parts can al-
of the cutting guide on
so be found under:
the workpiece. Slide the
www.bosch-pt.com
machine with moderate
Our customer service representatives can answer your ques-
feed, adapted to the ma-
tions concerning possible applications and adjustment of
terial to be worked.
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
English | 25
1 619 929 J35 | (13.5.11)

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Gws 8-125 professionalGws 10-125 professionalGws 11-125 ci professionalGws 11-125 cie professionalGws 14-125 ci professionalGws 14-125 cie professional ... Afficher tout

Table des Matières