Publicité
Compressor will be sufficient for tools at all production rates.
Le compresseur sera suffisant pour les outils à tous les taux de production.
El compresor será suficiente para las herramientas a cualquier velocidad de trabajo
Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
Le compresseur est suffisant pour les cadences de production lentes ou modérées, mais son rendement pourrait être
insuffisant pour les cadences très rapides.
El compresor será suficiente a velocidades de trabajo bajas o moderadas, pero puede tener dificultades en velocidades
muy rápidas.
Compressor will be adequate only when tools are utilized at slow production rates. (punch-out or occasional use)
Le compresseur est adéquat uniquement quand les outils sont utilisés à des cadences de production lentes (perforation ou
utilisation occasionnelle).
El compresor sólo será adecuado cuando las herramientas se utilicen en velocidades de trabajo lentas (perforación o uso
ocasional).
Not Recommended
Non recommandé
No recomendado
TYPICAL NAILS ACCEPTED BY THE D51823 AND D51845 FRAMING NAILERS
CLOUS TYPIQUES ACCEPTÉS PAR LES CLOUEUSES POUR CHARPENTE D51823 ET D51845
CLAVOS NORMALES ACEPTADOS POR LAS CLAVADORAS D51823 Y D51845
ROOF DECKING, SHEATHING AND SUBFLOORING
PANNEAUX DE TOIT, PANNEAUX DE REVÊTEMENT
ET SUPPORTS DE REVÊTEMENT DE SOL
PROTECCIÓN DE TEJADOS, REVESTIMIENTOS Y BAJO PISOS
Ring
Smooth
Shank
Shank
NAIL HEAD TYPES
TYPES DE TÊTE DE CLOUS
TIPOS DE CABEZAS DE CLAVOS
Full Round - D51845, 20˚ - 22˚ Collation
Tête ronde pleine - D51845, 20˚ - 22˚ regroupement
Cabeza redonda completa: D51845, unión de 20˚ - 22˚
Clipped Head - D51823, 31˚ - 34˚ Collation
Tête entaillée - D51823, 31˚ - 34˚ regroupement
Media cabeza: D51823, unión de 31˚ - 34˚
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS.
Trigger valve housing leaks
Top cap leaks air
Exhaust leaks
Air leaks around nose when tool is at rest.
(Driver blade in up position.)
Air leaks around nose when tool is in actuated
position. (Driver blade in down position.)
Tool does not cycle
in cold weather
Lack of power; sluggish
Skipping nails; intermittent feed
Fasteners jam in tool
(D51845 ONLY,
(D51845 ONLY,
SEULEMENT,
SEULEMENT,
SÓLO)
SÓLO)
Smooth
Screw
Shank
Shank
Troubleshooting Guide
CONTACT A D
WALT SERVICE CENTER OR CALL 1-(800)-4-D
E
O-ring or valve stem failure
Loose cap screws
Damaged or worn gasket or O-ring
Main seal or O-ring damaged, debris in tool.
Damaged or worn O-rings
Damaged or worn bumper
Tool not receiving air
Valve may be frozen
Damaged or worn O-rings
Broken or damaged driver blade
Low air pressure
Lack of lubrication
Damaged or worn O-rings
Exhaust port blocked or clogged
Depth adjustment set too shallowly
Driver damaged or worn
Air restricted
Lack of lubrication
Nosepiece screws loose
Wrong size/angle fasteners
Dirty magazine
Damaged/Worn magazine
Broken or damaged driver blade
Trigger valve O-ring worn or damaged
Worn piston O-ring
Worn or damaged pusher spring
Magazine loose
Driver channel in nosepiece worn
Wrong size/angle fasteners
Magazine loose
Worn driver blade
Nosepiece screws loose
Nails not feeding properly
FRAMING, DECK BUILDING AND STRUCTURAL
CHARPENTE, CONSTRUCTION DE TERRASSE ET STRUCTURE
MARCOS, CONSTRUCCIÓN DE TECHOS Y ESTRUCTURAS
Smooth
Ring
Shank
Shank
WALT.
E
Replace valve using Trigger Valve Kit: Cat.# D510005
Tighten cap screws using appropriate allen wrench
Replace gasket/O-rings using Nailer O-ring Repair Kit, Cat. # D518005
Replace gasket/O-rings using Framing Nailer O-ring Repair Kit, Cat. # D518005
Replace gasket/O-rings using Framing Nailer O-ring
Repair Kit, Cat. # D518005
Replace bumper using: Frame Nailer Bumper Kit, Cat. # D518006
Check air supply
Warm up tool. Lubricate with D
pneumatic oil containing ethylene glycol
Replace gasket/O-rings using Framing Nailer O-ring Repair Kit, Cat. # D518005
Replace Driver Blade using either Kit:
Driver Blade Kit for D51845 Full Round Head Nailer; Cat. # D518452
or Driver Blade Kit for D51823 Clipped Head Nailer; Cat. # D518232
Check air supply
Lubricate tool using D
E
Replace gasket/O-rings using Framing Nailer O-ring Repair Kit, Cat # D518005
Disconnect air, remove exhaust plate from top of tool, clean port
Reset depth adjustment
Replace driver blade
Check air supply and couplers
Lubricate tool using D
E
Tighten nosepiece screws using appropriate Allen wrench
Use only recommended fasteners
Clean magazine track and nosepiece
Replace magazine
Replace driver blade using either Kit:
Driver Blade Kit for D51845 Full Round Head Nailer; Cat. # D518452
or Driver Blade Kit for D51823 Clipped Head Nailer; Cat. # D518232
Replace valve using Trigger Valve Kit; Cat. # D510005
Replace O-ring using Framing Nailer O-ring Repair Kit, Cat # D518005
Replace spring using Magazine Pusher Spring Kit; Cat. # D518004
Check that magazine cam latch is holding firmly
Replace nosepiece
Use only recommended fasteners
Check that magazine cam latch is holding firmly
Replace driver blade using either Kit:
Driver Blade Kit for D51845 Full Round Head Nailer; Cat # D518452
or Driver Blade Kit for D51823 Clipped Head Nailer; Cat. # D518232
Tighten nosepiece screws using appropriate Allen wrench
Ensure nails are feeding properly through the magazine and into the nose.
5.5 HP Gas
Portable
Handcarry
2 HP Elec.
14 - 16 CFM
3.2 - 4 CFM
8 - 9 CFM
8 CH Essence
Portable à la
5.5 HP
14 à 16 pieds
main
Essence 2
CH Élec.
3,2 à 4 pieds
cubes par
8 à 9 pieds
minute
cubes par
Transportable
minute
3.2 - 4 CFM
5.5 CV Gas 2
CV Elec.
8 -9 CFM
1
2
3
4
5
6
7
8+
(D51845 ONLY,
(D51845 ONLY,
SEULEMENT,
SEULEMENT,
SÓLO)
Smooth
Smooth
Shank
Shank
WALT Pneumatic Tool Oil or winter weight
E
WALT pneumatic tool oil.
WALT pneumatic tool oil
8 HP Gas
Industrial
23+ CFM
Industriel
23 pieds
cubes par
cubes par
minute
minute et +
8 CV Gas
Industrial
14 -16 CFM
23+ CFM
SÓLO)
Publicité
