Table des Matières
Publicité
3.2 Safety at the workplace
a)
Make sure the workplace is orderly and well
lit. A messy or poorly lit workplace may lead to
accidents. Try to anticipate what may happen,
observe what is going on and use common sense
when working with the device.
b)
Do not use the device in an explosion hazard zone,
for example in the presence of flammable liquids,
gasses or dust. The device generates sparks which
may ignite dust or fumes.
c)
Upon discovering damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
d)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
e)
Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
f)
If a fire starts, use solely powder or carbon dioxide
(CO
) fire extinguishers suitable for use on live
2
devices to put it out.
g)
Children or unauthorised persons are forbidden
from entering a work station. (A distraction may
result in a loss of control over the device).
h)
Use the EMERGENCY STOP if there is a risk of injury
or death, accident of damage!
REMEMBER! When using the device, protect children
and other bystanders.
3.3 Personal safety
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
When working with the device, use common sense
and stay alert. Temporary loss of concentration
whilst using the device may lead to serious injuries.
c)
Use personal protection equipment as required
for working with the device, specified in section 1
(Legend). The use of correct, approved personal
protection equipment reduces the risk of suffering
an injury.
d)
To prevent the device from accidentally switching on,
make sure the switch is on the OFF position before
connecting to a power source.
e)
Do not overestimate your abilities. When using the
device, keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
f)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
g)
If suction is to be connected to the device, check
all connections and make sure they are tight. Using
a de-dusting system may reduce the risk associated
with dust.
h)
Remove all adjusting tools or spanners before
turning the device on. A tool or spanner left in the
revolving part of the device may cause injury.
3.4 Safe device use
a)
Do not overload the device. Use appropriate tools
for the given task. A correctly selected device will
perform the task for which it was designed better
and in a safer manner.
8
b)
Do not use the device if the ON/OFF switch does not
function properly (does not switch the device on and
off). Devices which cannot be switched on and off
using the ON/OFF switch are hazardous, should not
be operated and have to be repaired.
c)
Make sure the plug is disconnected from the
socket before attempting any adjustments, tool
replacements or before putting the device aside.
Such precautions will reduce the risk of accidentally
activating the device.
d)
When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
e)
Maintain the device in a good technical state. Before
each use, check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
f)
Keep the device out of the reach of children.
g)
Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
h)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
i)
When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country where the device will be used.
j)
Avoid situations where the device halts during
use due to excessive loading. This may result in
overheating of the drive elements and device
damage.
k)
Do not touch articulated parts or accessories, unless
the device has been disconnected from a power
source.
l)
Do not touch any articulated parts or accessories
unless the power source has been disconnected.
m)
Use your tool at a lower input load than specified
on the nameplate to increase working efficiency and
decrease wear out.
n)
Properly set the tool holder in the machine.
o)
The tool becomes very hot during operation.
Failure to follow safety recommendations and instructions
may result in serious injuries or death!
4. Use guidelines
SCOPE OF APPLICATION
The telescopic sander is designed for sanding plastered
interior and exterior surfaces, ceilings, smoothing surfaces
and sanding surfaces with limited access even at significant
heights.
The drywall sander with a vacuum is designed for sanding
walls and ceilings made out of plasterboards, etc.
The user is liable for any damage resulting from non-
intended uses of the device.
4.1 Device description
Model MSW-TDW750LB:
Rev. 01.03.2018
10
7
9
6
8
11
5
3
4
12
2
1
1.
motor
2.
carbon brushes cover
3.
device arm
4.
LED light
5.
LED light switch
6.
rotational speed adjuster
7.
ON/OFF trigger lock
8.
ON/OFF trigger
9.
telescopic pipe extension clamp
10.
handle
11.
hose
12.
dust bag
Model MSW-TDW750ECO
3
4 5 6
1
2
9
10
7
8
1.
head removal button
2.
device folding pin
3.
rotational speed adjuster
4.
ON/OFF trigger lock
5.
ON/OFF trigger
6.
telescopic pipe extension clamp
7.
motor
8.
LED light with switch
9.
handle
10.
rear handle
Model MSW-DWS750WB
10
9
1
2 3 4
5 6 7
8
1.
vacuum hose/dust discharge hose connection
2.
adjustment knob
3.
grinding head housing
4.
handle
5.
rotational speed adjuster
6.
ON/OFF trigger
7.
ON/OFF trigger lock
8.
front head housing
9.
LED light
10.
dust exhaust speed adjustment
Rev. 01.03.2018
4.2 Preparing for use
Model MSW-DWS750WB | MSW-TDW750LB:
•
MSW-TDW750ECO DEVICE ASSEMBLY:
After unpacking the device, connect both ends of the hose.
To do that, align both holes, latch the pin and then close it:
•
Attaching the hose to the device and to the bag:
To attach the hose to the device or bag, insert the hose end
into the discharge hole until both fasteners snap into place.
A
To remove the hose from the device or the bag, press
(using a screwdriver for example) both fasteners towards
the centre of the hose and pull the hose out.
To attach the hose to the vacuum, insert the hose end into
the vacuum discharge hole. Use a hose clamp to ensure
the hose does not fall out of the vacuum when in use. To
remove the hose from the device, pull the hose handle
(make sure the hose clamp, if such was used, has been
removed).
•
Telescopic pipe assembly:
(only for MSW-TDW750LB and MSW-TDW750ECO):
To attach the telescopic pipe, pull back the telescopic pipe
extension clamp, loosen the screw and then insert the pipe
into the hole in the device handle:
Tighten the screw and close the clamp.
4.3 Device use
•
Models: MSW-TDW750LB | MSW-TDW750ECO:
To switch the device on, move the ON/OFF trigger to the
ON position, select the required rotational speed range
and start using the device. In order to turn the device off,
move the ON/OFF trigger to the OFF position. The device
has a LED light, which can be switched on and off using
the LED light switch independently of whether the device
is on or not.
•
Model MSW-DWS750WB:
To start the device, press and hold trigger (1) and then
press and hold button (2), trigger (1) may be released. To
switch the device off, release button (2). Use the rotational
speed adjuster knob (4) to select the required speed:
4
2
1
The LED light will come on automatically when the device
is started. The LED light will automatically go out after the
device is switched off.
9
Publicité
Table des Matières
