Device Description; Device Use; Cleaning And Maintenance - Steinberg Systems SBS-MK-1 Manuel D'utilisation

d) Keep the device in perfect technical condition. If
damage is discovered, hand over the device for repair
before use.
e) Keep the device out of the reach of children.
f) Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
g) To ensure the operational integrity of the device, do
not remove factory-fitted guards and do not loosen
any screws.
h) Do not move, adjust or rotate the device in the course
of work.
i) Clean the device regularly to prevent stubborn grime
from accumulating.
j) The device is not a toy. Cleaning and maintenance may
not be carried out by children without supervision by
an adult person.
k) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
l) Keep the device away from sources of fire and heat.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there is
still a slight risk of accident or injury when using the
device. Stay alert and use common sense when using
the device.
3. USE GUIDELINES
The microscope is used to observe small objects or details
invisible to the unaided eye. The product is intended for
EN
home use only!
The user is liable for any damage resulting from
unintended use of the device.

3.1. DEVICE DESCRIPTION

ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 31).
1. WF 10x eyepiece
2. WF 16x eyepiece
3. Barlow lens
4. MicrOcular
5. Tube
6. Stand
7. Screw
8. Revolver
9. Lens
10. Clips
11. Microscope table
12. LED lighting (transmitted light)
13. Base
14. Backlight selection dial
15. Power
16. Focus ring:
a) macrometric
b) micrometric
17. Colour filters
18. LED lighting (reflected light)
19. Disc with Ulead Photo Explorer SE software
20. 10 slides, 10 glass slips and 5 plastic specimen boxes
21. Specimens:
a) Yeast
b) „Gum Media" adhesive
c) Sea salt
d) Shrimp eggs
22. Transformer with plug and power cable
23. Sample slicer
24. Shrimp hatchery
25. Tweezers
26. Pipette
27. Case
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C. Ensure good ventilation in the room in which
the device is being used. There should be at least 10 cm
distance between each side of the device and the wall or
other objects. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface. Position the device such that you always have
access to the power plug. The power cord connected to the
appliance must be properly grounded and correspond to
the technical details on the product label.

3.3. DEVICE USE

3.3.1 CORRECT MICROSCOPE ADJUSTMENT
1. Loosen the screw [7].
2. Place the stand in a position convenient for the user.
3. Adjust the microscope table to the lowest position.
4. Turn the revolver until it clicks at the lowest
magnification.
5. Insert the 10x eyepiece into the tube.
6. To double the image magnification, place a Barlow
lens between the tube and eyepiece.
NOTE: To avoid damage, always set the microscope
table to the lowest position before changing the lens
position.
1 2
5
3
3.3.2. USING THE ELECTRIC LED LIGHTING
1. Connect the power cord to the socket on the back of
the microscope.
2. Insert the plug into the power socket.
There are two diodes on the microscope. The first illuminates
the sample from below, the second from above. Using the
knob [14], you can select the lighting method depending on
the type of object:
It. Lighting type Object type
I from bottom
transparent
(transmitted light)
II hard,
from above
(reflected light) non-transparent
II from bottom
half-transparent
and from above
8
3.3.3. USING COLOUR FILTERS
The colour filters [17] are located below the microscope
table. This option is helpful when observing very bright
objects. It makes it easier to recognize the components of
colourless or transparent objects.
3.3.4. OBSERVING AN OBJECT
1. The slide should be inserted under the clips [10] on
the microscope table [11] centrally under the lens [9]
and above the lower LED lighting [12].
20
8
2. Specimen observation should be started at the lowest
magnification. This will help centre the object and
focus the image. The higher the magnification, the
more light is needed to get a good image.
3. In the next step, look into the eyepiece and gently
turn the focus ring [16] until the image becomes
bright and sharp. This procedure should be repeated
after each change or adjustment of the eyepiece.
4. To increase the magnification, install the 16x eyepiece
and turn the revolver [8] to higher settings (10x or
40x).
NOTE: Please note that the highest magnification is
not the best for all specimen.
3.3.5. SPECIMEN PREPARATION
Place the object on the slide and use a pipette to put a few
drops of distilled water on it. Place the glass slip vertically on
the edge of the water droplet and slowly lower it.
3.3.6. SAMPLE PREPARATION - SLICES
NOTE: Samples should be prepared by adults or under their
supervision. Heat a little wax or paraffin and immerse in it
the object from which the sample will be prepared. Leave
the object to harden. Using a sample slicer [23] (alternately
a knife or a scalpel), cut very thin slices from the waxed
object. The slice should be placed on a slide and covered
with a glass slip.
3.3.7. MICROCULAR INSTALLATION
NOTE: after the MicrOcular is inserted, the zoom settings
change and must be readjusted.
1. Remove the Barlow lens [3] and the eyepiece [1/2].
2. Join the MicrOcular [4] with the eyepiece [1/2] and
insert in the tube.
3. Install software and drivers.
4. Reboot the computer after downloading the system
and connect the MicrOcular to a USB port.
3.3.8. INSTALLING THE ULEAD PHOTOEXPLORER 7.0 SE
SOFTWARE
After assembling the microscope, do not connect the
MicrOcular to the computer. Work with the microscope
should be started from software installation.
1. Insert the CD into the CD drive, the menu will open
automatically.
2. Click „Install PhotoExplorer 7.0 SE".
3. Select your preferred language from the list and click
„OK".
4. On the welcome screen, click „Continue".
5. A License Agreement will appear, which you must
accept by clicking „Yes".
6. Write the name and serial number from the CD
packaging; the „Company Name" field can be left
blank. Click ‚Continue'.
7. In the next 4 windows select „Target Path", „Create
Icons", „Select Program Folder" and „TV system" and
accept the information by clicking „Continue".
8. The „Setup Status" window will appear, the program
files are then copied to your computer, which may
take several minutes.
9. When the a/m window disappears, another one will
appear after a while. If the program is used in the
future to display and edit photos, click „Continue", if
not select „Do not Change Current File Allocation",
then select „Continue".
10. If the Internet Explorer opens, close it.
11. When the „Install Shield Wizard Complete" window
appears, you can click „No, I will restart computer
later" and press „Finish". The software has been
installed.
3.3.9 DRIVER INSTALLATION
Make sure that MicrOcular is not connected to the computer.
1. Click "Install Bresser PC-Ocular Driver'.
2. Select your preferred language from the list and click
„OK".
3. On the welcome screen, click „Continue".
4. Select „Complete" and click „Continue".
5. In the „Start Copying" window, select „Continue"
again.
6. The „Setup Status" window will appear, the program
files are then copied to the computer, which may take
several minutes.
7. When the „InstallShield Wizard Complete" window
appears press „Finish". Drivers have been installed.
Click "Exit" in the menu.
3.3.10 MICROCULAR - DISPLAYING AND SAVING PHOTOS
1. Turn on Ulead PhotoExplorer 7.0 SE.
2. Select „Video", then „Record Picture" from the menu.
3. The „Record Picture from Video Unit" window will
appear, click „Live View".
4. The image from the MicrOcular should be visible
on the screen (if it is not, click „Setup" and select
„Options"; the „Recording Unit" window will appear.
In „Select Camera", select „Microcular" and accept by
clicking „Ok" ).
5. Focus again. If the image is clear click „Record Now".
6. The image has been saved to your computer.
7. Click ‚Close' and the photo will appear in Ulead
PhotoExplorer.
NOTE: the detailed program manual can be found on
the CD in the „Document / Manual" folder. If the folder
does not include the language of the user, a message
can be sent to Ulead asking for the availability of the
user's language.

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug before each cleaning,
adjustment or replacement of accessories, or if the
device is not being used.
b) Use only non-corrosive cleaners to clean the surface.
9
EN