Maintenance, Cleaning And Storage - Solo Cleanline 305A Instructions D'emploi

Pulvérisateur à pression préalable cleaner
Masquer les pouces Voir aussi pour Cleanline 305A:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18

5 Maintenance, cleaning and storage

5.1 Greasing the cap gasket
5.2 Greasing the pump piston sealing ring
If the pump is hard to operate, the sealing ring of
the pump piston (Fig. 7, pos. 12, part no.
model series A: 00 62 149
model series B: 00 62 369)
should be greased with silicone grease or replaced
if necessary.
Disassembly of the pump and greasing the
sealing ring:
Fig. 4: Ensure the sprayer is empty and not
pressurised. Place sprayer securely on level
ground. If the pump is completely screwed onto the
tank, loosen the pump with 1–2 turns.
Fig. 5: Firmly hold the pump handle with both
hands and push downwards until the pump
releases from the flange housing with an audible
click. Unscrew the blue flange housing from the
sprayer and remove the pump from the tank.
Fig. 6: Use a screwdriver to lever both black flange
semi-circles from the pump cylinder. The pump
piston can now be pulled from the pump cylinder.
Fig. 7: The sealing ring (12) can now be re-greased
with silicone grease or replaced if damaged.
Assembly:
Fig. 8: Place the blue flange housing correctly on
the pump piston.
Push the pump piston into the pump cylinder.
Push both black flange semi-circles onto the pump
cylinder until they lock with an audible click.
Fig. 9: Place the pump cylinder securely on level
ground. Line up the blue flange housing in the
exact position and firmly push the red flange
housing down with both hands onto the pump
cylinder until the parts lock together with an audible
click.
ENGLISH 9
Fig. 10:
For proper sealing of the
spraying agent tank, the
cap gasket (10) must be
well greased with silicone
grease.
5.3 Draining the spraying agent tank and
cleaning the spraying agent carrying
parts
Before opening the spraying agent tank and before
disassembling the nozzle attachment, depressurise
the device by pulling on the pressure relief valve
(Fig. 3).
Before pulling on the pressure relief valve (4), the
device must always be in an upright position.
Attention: Keep the device away from your face!
Empty the pressure sprayer after use every day.
Collect and dispose of the residual quantity of the
spraying agent according to the applicable law and
provisions. Observe the information from the
spraying medium manufacturer. Flush the spraying
agent tank and all spraying-agent-conducting parts
thoroughly with clean water. Operate the pressure
sprayer once more with clear water.
Let the spraying agent tank dry again in the open
condition after cleaning.
Clean the spraying nozzle as follows after every 50
uses, or if the spraying pattern grows uneven, or if
much less spraying agent then before is
dispensed:
Cleaning the spray nozzle:
 Rinse the nozzle attachment with clean water.
 Disassemble the nozzle attachment (Fig. 2).
 Clean the O-rings and the spray nozzle with
clean water and a soft brush.
Never use your mouth to blow through the spray
nozzle! Never use hard objects to clean the
nozzles!
 Reassemble the components of the nozzle
attachment (Fig. 2).
5.4 Taking the sprayer out of service and
putting it into storage
Prepare the device for storage according to
section 5.3. .
Store the device protected from sunlight in a
secure, dry and frost-free location under a
maximum ambient temperature of 35 °C [95 °F].
There must not be any open fires or similar
nearby.
Ensure that the unit cannot be used by
unauthorised persons, in particular children.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Cleanline 307aCleanline 305bCleanline 307b

Table des Matières