Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Safety precautions
for grounded tools
Warning:
When using electric tools, basic safety precautions should
always be followed to reduce the risk of fire, electric shock,
and personal injury, including the following:
Read all instructions
1. Keep Work Area Clean. Cluttered areas and benches invite injuries.
2. Consider Work Area Environment. Don't expose power tools
to rain. Don't use power tools in damp or wet locations. Keep work area
well lit. Do not use tool in presence of flammable liquids or gases.
3. Guard Against Electric Shock. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
4. Keep Children Away. Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store Idle Tools. When not in use, tools should be stored in dry, and
high or locked-up place – out of reach of children.
6. Don't Force Tool. It will do the job better and safer at the rate for which
it was intended.
7. Use Right Tool. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended – for example –
don't use circular saw for cutting tree limbs or logs.
8. Dress Properly. Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-skid footwear are recom-
mended when working outdoors. Wear protective hair covering to contain
long hair.
9. Use Safety Glasses. Also use face or dust mask if cutting operation is
dusty.
10. Don't Abuse Cord. Never carry tool by cord or yank it to disconnect
from receptacle. Keep cord from heat, oil, and sharp edges.
11. Secure Work. Use clamps or a vise to hold work. It's safer than using
your hand and it frees both hands to operate tool.
12. Don't Overreach / Maintain Control. Keep proper footing and bal-
ance at all times.
13. Maintain Tools With Care. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing acces-
sories. Inspect tool cords periodically and if damaged, have repaired by
authorized service facility. Inspect extension cords periodically and replace
if damaged. Keep handles dry, clean, and free from oil and grease.
14. Disconnect Tools. When not in use, before servicing and when chang-
ing accessories, such as blades, bits, cutters.
15. Remove Adjusting Keys and Wrenches. Form habit of checking to
Printed: 07.07.2013 | Doc-Nr: PUB / 5071192 / 000 / 00
see that keys and adjusting wrenches are removed from tool before turn-
ing it on.
16. Avoid Unintentional Starting. Don't carry tool with finger on switch.
Be sure switch is off when plugging in.
16A. Extension Cords. Make sure your extension cord is in good condi-
tion. When using an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating. The follow-
ing table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavler the cord.
Extension Cord Table
Volts
Total Length of Cord in Feet
120 V
0–25
26– 50
240 V
0–50
51–100
Ampere Rating
AWG
More Than
Not More Than
0
6
18
16
6
10
18
16
10
12
16
16
12
16
14
12
17. Outdoor Use Extension Cords. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
18. Stay Alert. Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
19. Check Damaged Parts. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Do
not use tool if switch does not turn it on and off.
20. Only use specified accessories and attachments which are given in
the operating instructions or in the respective catalogue. The use of acces-
sories or insert tools or attachments other than those specified in the oper-
ating instructions can result in personal injury to you.
21. Only have repairs carried out by recognized electrical specialists.
This electric tool/machine complies with respective safety regulations.
Repairs may only be carried out by an electrical specialist otherwise an
accident hazard for the operator can exist.
22. Wear ear protectors when using for extended periods.
23. Always use any supplied side handle, and keep it tightly secured;
use both hands during operation. Keep proper footing and balance and
don't overreach. Firm control of the tool is necessary should the tool bind.
Warning: To improve reliability, the torque of this tool has been increased,
which can cause serious injury if not properly controlled. When drilling
always use the 9≤side-handle and grasp it at the outermost end to main-
tain control. Be prepared – the bit can bind at any time!
24. Hold Tool by Handle(s) Provided. Do not touch uninsulated parts of
tool when drilling. Exposed metal surfaces may be made live if the tool
drills into electrical wiring.
25. Grounding instructions. This tool should be grounded while in use to
help protect the operator from electric shock. The tool is equipped with a
3-conductor cord and 3-prong grounding type plug to fit the proper
grounding type receptacle. The green (or green and yellow) conductor in
the cord is the grounding wire. Never connect the green (or green and
yellow) wire to a live terminal. If your unit is for use on less than 150 V, it
51–100 101–150
has a plug that looks like that shown in sketch (A) in Figure «Grounding
101–200 201–300
Methods». An adapter, see sketches (B), is available for connecting sketch
(A) type plugs to 2-prong receptacles. The green-colored rigid ear, lug, or
the like, extending from the adapter must be connected in a permanent
ground, such as a properly grounded outlet box.
16
14
14
12
14
12
GROUNDING METHODS
Not recommanded
grounding pin
26. Extension Cords. Use only 3-wire extension cords that have 3-prong
grounding-type plugs and 3-pole receptacles that accept the tool's plug.
Replace or repair damaged cords.
Save these instructions.
metal screw
cover of grounded
outlet box
(A)
(B)
Publicité
Table des Matières
