Technical Data; Before Starting The Equipment - Royal RPC 2040 Mode D'emploi D'origine

Anleitung_RPC_2040_SPK1__ 12.11.12 08:52 Seite 21
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
L sound pressure level (ISO 22868)
PA
K uncertainty
PA
L sound power level measured
WA
(ISO 22868)
K uncertainty
WA
L sound power level guaranteed
WA
(ISO 2000/14/EC)
A vibration (front handle)
hv
(ISO 22867)
K uncertainty
hv
A vibration (rear handle)
hv
(ISO 22867)
K uncertainty
hv
Chain type
Bar type
Spark plug
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
46 cm 3
Wear protective gloves.
n
2 kW
36 cm

5. Before starting the equipment

16" (40 cm)
(3/8"), 9.525 mm
Important: Do not start the engine until the saw
1.27 mm
is fully assembled.
3300 ± 200 rpm
Important: Wear protective gloves at all times
11000 rpm
when handling the chain.
550 ml
260 ml
5.1 Fit the chain bar
Yes
To ensure that the bar and the chain are supplied
7 x 9.525 mm with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
Yes
build-up of residue.
Yes
1. Make sure the Chain brake lever is pulled back
Yes
into the DISENGAGED position (Fig. 3A).
- 2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
5.5 kg
3. Using a screwdriver, run the adjustment screw (D)
7 kg
COUNTERCLOCKWISE until the TANG (E)
560 g / kWh
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3C).
99 dB(A)
4. Fit the open end of the chain bar over the die bar
3 dB(A)
pins (F) (Fig. 3D).
5.2 To install saw chain
111 dB(A)
1. Spread chain out in a loop with cutting edges (A)
3 dB(A)
pointing CLOCKWISE around loop (Fig. 4A).
2. Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
114 dB(A)
sprocket teeth (Fig. 4B).
3. Guide the drive links into the groove (D) and
7.5 m/s 2
around the end of the bar (Fig. 4B).
1.5 m/s 2
NOTE: The saw chain may droop slightly on the lower
part of bar. This is normal.
7.0 m/s 2
GB
1.5 m/s 2
Carlton N1C-BL-57-EB
Kangxin AP16-57-507P
L8RTF/NHSP LD
21