Cleaning And Care - WMF STELIO Mode D'emploi

Propulsion Unit
You can set the speed of the high-performance motor to 5 levels using the
selector switch on the propulsion unit.
The motor will operate at maximum speed for as long as you keep the
selector switch on the pulse level P. This is particularly useful when crushing
ice cubes.
Glass Jar
The closing cap in the lid can be removed by rotating it counter-clockwise.
The glass jar can be dismantled, especially for cleaning. To do so, place the
jar on the table with the opening facing down and rotate the screwed ring
counter-clockwise. You can now remove the blade assembly and the sealing
ring.
To assemble, the sealing ring is first attached to the blade assembly. When
doing so, make sure the sealing ring is properly seated on the blade assembly.
Then place the blade assembly in the glass jar. Now place the screwed ring on
the glass jar and rotate in a clockwise direction.
Note: In order to ensure the tightness of the glass jug, the threaded ring must
be screwed on tightly. The threaded ring is easier to tighten if you apply a
few drops of cooking oil on the sealing side of the glass jug (see figure).
Start-up
Clean the glass jar, lid and closing cap prior to the first use. Make sure that
you do not injure yourself on the sharp blade.
Place the selector switch on the off position 0 and set the glass jar on the
propulsion unit as shown in the diagram.
Add the first ingredients, close the glass jar with the lid and closing cap and
place the selector switch on the desired operating mode.
Note: only food with a maximum temperature of 60°C may be processed.
Speed Use
Instant drinks, soft fruits and cocktails
1 - 2
with alcohol
1 - 2 Milkshakes
Soups, milkshakes with harder fruits
1 - 2
Sauces, baby foods, vegetables
3 - 5
3 - 5
Nuts, hard cheese, dry bread
Additional ingredients may be added by removing the closing cap while the
motor is running.
10
Maximum time
40 - 60 s
1 - 2 min
1.5 - 2 min
1.5 - 2 min
40 - 60 s
Crushing ice cubes
Fill with a maximum of 10 ice cubes and close the glass jar with the lid and
closing cap. Place the selector switch for a few seconds on the pulse stage P and
then back on the off position 0. As soon as the ice cubes fall back to the bottom
of the glass jar, you can switch to the pulse stage P again for a few seconds.
Repeat the process for as many times as needed for the ice to reach the desired
consistency.
General Information
1.25 l is recommended as the maximum fill level. Filling past this amount may
lead to overflowing depending on the consistency of the ingredients.
Switch the device off as soon as the amount is processed. Never operate the
device empty.
Allow the device to cool down following the maximum operating time so that the
motor is not overloaded.
For large volumes, especially thin fluid content, it is hard to pour in a directed
manner. In this case, it is better to prepare the batch in parts.
Always place the selector switch on the off position 0 before removing the glass
jar.
Attention! Risk of injury! Always wait for the blades to come to a standstill
before removing the lid. Do not reach into the device before the power plug
has been unplugged.
Completely empty the glass jar following use. Do not leave any liquid in the jar.

Cleaning and Care

Remove the power plug after use.
Never submerge the propulsion unit in water, but rather only wipe the outside of
it with a damp cloth. Do not use any abrasive cleaning agents.
Be sure to avoid injury on the sharp blades when cleaning the glass jar.
Immediately after mixing, fill the jar with warm rinsing water and allow the
motor to run for a few seconds. Then remove the glass jar and clean with a
washing-up brush.
For thorough cleaning, you can dismantle the glass jar as described in the section
entitled „Glass Jar".
For quick and easy cleaning, you can place all loose parts in the dishwasher.
11