Setting The Functions - Trixie Reptiland Notice D'utilisation

3. Setting the functions

3.1 Setting the time (real time):
Press the Mode button until 'T' starts flashing in the display. Now
press SET for more than 3 seconds until the hour digit flashes to
open the menu for time setting. Set the hour with the arrows
and . Then press SET again to open the menu for minutes, and
set those with the arrows.
3.2 Setting the start time for day mode:
Press the Mode button until 'T1' starts flashing in the display. Now
press SET for more than 3 seconds until the hour digit flashes. Set
the hour with the arrows. After that press SET again to open the
menu for setting the minutes with the arrows.
3.3 Setting the start time for night mode:
Press the Mode button until 'T2' starts flashing in the display. Press
SET for more than 3 seconds until the hour digit starts flashing.
Now follow the same steps as for day time. The setting in 'T1'
must be lower than in 'T2'.
3.4 Setting a temperature for day mode:
Press the Mode button until 'ST1' starts flashing in the display.
Now press SET until the temperature display starts flashing. Set
the temperature with the arrows. After setting the temperature
open the menu for switching delay (1 to 15 °C) by pressing SET
again. Set the switching delay with the arrows. Pressing SET again
after this will open the menu for heating (H) or cooling (C) mode.
Again use the arrows to set the temperature.
3.5 Setting a temperature for night mode:
Press the Mode button until 'ST2' flashes in the display. Now press
the SET button for more than 3 seconds until the temperature
display starts flashing. Follow the same steps as for day time.
3.6 Setting the humidity for day mode:
Press the mode button until 'SH1' starts flashing in the display.
Now press the SET button for more than 3 seconds until the
humidity display starts flashing. Use the arrow keys to set the
humidity. After this press SET again to open the menu for switching
delay (1 to 20 %). Use the arrow keys to set the switching delay.
3.7 Setting the humidity for night mode:
Press the mode button until 'SH1' starts flashing in the display.
Now press the SET button for more than 3 seconds until the
humidity display starts flashing. Now continue as in day mode.
3.8 Setting the timer mode for the thermostat:
Press the Mode button until 'A' flashes in the display. Now press
SET for more than 3 seconds until 'A1' (ON time) flashes in the
display. Choose the hour with the arrows. Next press SET again to
set the minutes with the help of the arrows. Press SET again to set
the seconds. Pressing SET again will open the menu for 'OFF' time
(A2). Again program hours, minutes and seconds with the arrows.
For three more 'ON' and 'OFF' times go through the same steps
as for 'A1' and 'A2'. If you do not need any more 'ON' /'OFF' times
(A3 – A8), put them on default (see table 'menu'). The 'ON' time
must always be lower than the 'OFF' time.
3.9 Setting the timer mode for the clock timer:
Press the Mode button until 'B' flashes in the display. Now press
SET for more than 3 seconds until 'B1' ('ON' time) starts flashing.
For setting the 'ON' and 'OFF' times follow the same steps as for
setting the timer mode for the thermostat. If you do not use the
other 'ON'/'OFF' times (B3 to B8), set them to default (see table
'menu'). The 'ON' time must always be lower than the 'OFF' time.
6 TRIXIE Heimtierbedarf GmbH & Co. KG · D-24963 Tarp · www.trixie.de
3.10 Setting the timer for the hygrostat:
Press the mode button until 'C' starts flashing in the display. Now
press the SET button for longer than 3 seconds until 'C1' (ON
time) starts flashing. For setting the ON/OFF times proceed as for
setting the timer for the thermostat. If you do not use more ON/
OFF times (C3 to C8) set them to default (see table 'menu'). The
ON time always has to be smaller than the OFF time.
3.11 Setting the alarm mode for max. temperature:
Press the arrow for more than 3 seconds until the temperature
display starts flashing. Now press the arrow
alarm value (1 to 15 °C). The (visual) alarm signal starts when the
temperature set in 3.4 is exceeded by the pre-set alarm value.
Default is 0 °C.
3.12 Setting the alarm mode for min. temperature:
Press the arrow for more than 3 seconds until the temperature
display starts flashing. Now press the arrow
alarm value (1 to 15 °C). The (visual) alarm signal starts when
the temperature plus switching delay set in 3.5 falls below the
pre-set alarm value. Default is 0 °C.
3.13 Automatic Saving:
If there are no new entries with the buttons for 30 seconds, the
device automatically switches to operating mode. The settings
you have chosen will be saved.
3.14 After you have chosen your settings:
Press the Mode button after you have made all settings. The
thermostat will automatically switch to operating mode.
3.15 Reset to default:
Press the 'Reset' switch on the back of the device for more than
3 seconds.
4. Important information:
The device may only be connected to 230 V/ 50/60 Hz AC
•
Voltage.
• No changes may be made to the device and the device may
not be opened.
• Check device and sensor cables for damage before use. If you
observe any damage or faulty operation, the device may not
be used and must be unplugged. The same applies if the device
has come into contact with liquids. Only a qualified electrician
may carry out maintenance and repairs.
• If in doubt, contact professional experts or the manufacturer.
• To avoid accidents and loss of animals regularly check the
temperature and the settings. Any claims for damages due to
failure of the control system are excluded.
• Please note that the use of a thermostat reduces the lifetime
of lighting fixtures (bulbs and spotlights) due to frequent
switching on and off. Furthermore, frequent switching on and
off can disturb animals.
• The allowed ambient temperature during operation is 0 to 60 °C.
• Protect humidity sensor from direct contact with water.
• The device may only be used in dry clean rooms.
• If condensation forms, a drying time of up to 120 minutes is
needed before the device can be switched on again.
• Protect the device from moisture, splash water and direct heat.
• Never connect or disconnect the plug with moist or wet hands.
• This device comes with an overcurrent protection (electronic
fuse). If the fuse is activated, it can only be deactivated after
15 minutes at the earliest by pressing the safety button on the
junction box. Before switching it on again, the device needs
to be disconnected from the power supply and all plug-in
connections of the installation need to be checked.
again to set the
again to set the