Safety Instructions - Peach PS500-70 Mode D'emploi

UK

SAFETY INSTRUCTIONS

●
Read and follow all instructions carefully. Keep these
instructions for future reference.
●
Always turn off and unplug the machine before
moving, cleaning or anything other than normal operation.
Otherwise serious injury may result. Clean shredder with
a damp cloth, using a mild soap and water solution.
●
Do not use abrasives or solvent-based cleaners.
●
Turn the power switch off before removing the waste
bin E . It is advisable to disconnect the power cord
before opening the shredder.
●
This product should never be placed near a radiator or
other heat source.
●
Do not allow anything to rest on the power cord. Do
not place the power cord where people may walk on it.
●
Do not attempt to service this product yourself, as
opening or removing covers may expose you to the risk of
injury. Also, doing this will void the shredder's warranty.
●
Unplug this product and contact technical support if:
– The power cord or plug is damaged or frayed.
– Liquid has been spilled on the product.
– The product has been exposed to rain.
– The product does not operate normally, even when the
operating instructions are followed.
– The product has been dropped, or the casing has been
damaged.
●
This shredder should be operated only with an operator
in attendance.
Description of parts
A Switch
B LED "OVERHEAT"
C LED "OVERLOAD"
D LED "POWER"
E Waste bin
F Transparent window
Installation / Setup
●
The switch A located on top of the housing has 3
positions.
●
Make sure the switch is set to the "OFF"position.
●
Connect the power cord to any standard 230 Volt AC
outlet.
●
It is normal for residual lubricant in the motor to
burn off during the first several extended uses of your
shredder. Should you notice a slight burning odor or the
presence of small wisps of smoke during the first several
extended uses, you may continue using the shredder. If
3
Operating Instructions
either symptom continues to occur after repeated use,
please contact technical support for assistance.
Normal Operation
●
Move the switch A to the "AUTO" position, the red
LED "POWER" D will light up.
●
Insert paper to activate. The shredder starts
automatically and will stop as soon as all the paper has
gone through.
●
2
The shredding capacity is 14 sheets (80g / m ) or 1
CD resp. Credit Card. However, you should shred only
one type of these items at a time to avoid causing an
overload.
●
Never attempt to shred sealed envelopes. Doing so
may damage the shredder. Always remove and unfold
envelope contents completely before attempting to shred.
NEVER shred envelopes, labels or anything with glue or
any sticky substance as this will lead to paper jams.
●
Do not shred any wet paper, carbon paper, or vinyl
bags. The waste will stick in the cutter and may lower the
shredding performance.
●
Although the shredder can safely shred staples
and paper-clips, you should remove them if possible.
Industrial staples must be removed.
Paper Jam
●
If too much paper has been inserted, a jam may result.
In such a case the red LED "OVERLOAD" C will light up.
●
To clear the jam, empty the waste basket E first and
install the basket again
●
Move the switch A to the "REV" (rewind) position to
clear the shredder of paper that has not passed through
properly.
●
If not all the paper can be cleared, set the switch to the
"AUTO" (forward) position to help the remaining paper to
pass through.
●
This procedure may be repeated several times until the
jam is cleared.
Waste bin
●
The waste bin E needs to be emptied regularly, latest
if the transparent window F of the basket is covered
with waste paper.
Overheat
●
The shredder may be operated non-stop up to 30
minutes. After a short waiting time of 10 minutes,
shredding may continue.
●
In case of too long continuous operation, the device
switches off and the red LED "Overheat" B lights up.
In this case the switch A should be set to the "OFF"
position. The shredder will start it's normal functioning
as soon as the engine has cooled down enough.
Maintenance
●
It is recommended to lubricate the cutting blade from
time to time with Peach oil paper PS100-00 or Peach
Shredder oil PS100-05. This will increase the working life
of the cutting unit.
●
Empty the waste bin E.
●
Set the switch A to "AUTO".
●
Run the oil paper (Caution: Do not open the bag)
through the shredder. Then let the unit run backwards
(switch to "REV") for about 10 seconds.
●
Peach oil paper PS100-00 and Peach Shredder oil
PS100-05 are available from your dealer and in various
online shops.
4