Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Power consumption P1 (W)
2300
2500
2800
W
o
r
k
i
n
g
w
i
t
h
t
h
e
W
o
r
k
i
n
g
w
i
t
h
t
h
e
Choose a working position alongside the equipment or be-
hind it. Never stand near the ejection opening.
Longer material that is protruding from the device could
spring back when it is drawn in by the blades! Observe safety
distance!
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into the
filler funnel, ejection channel or in the vicinity of other moving
parts.
Check that no chopped residues are in the filling hopper be-
fore switching on the equipment.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones, bottles
or other objects unintended for processing, enter the filling
hopper.
Immediately switch off the equipment and allow it to come to a
stop, if foreign objects enter the filling hopper or if the equip-
ment starts to make unusual noises or vibrates. Remove the
mains plug and carry out the following checks:
inspect for damage,
−
replace or repair damaged parts,
−
− check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
•
all types of branches up to a max. diameter, depending on
wood species and freshness.
• withered garden refuse which has lain a number of days.
Only shred in alternation with branches.
No:
•
glass, metal, plastic, plastic bags, stones, cloth, roots with soil
•
refuse which does not have a solid consistency, e. g. kitchen
waste
Special tips on shredding:
Always fill the material to be shred-
ded into the filling hopper from the
right.
Branches, twigs and wood should
be broken down immediately after
they have been cut.
Material of this kinds gets very hard when it is dry, and the
−
maximum allowed branch diameter to be processed has to
be reduced.
Remove any side shoots from branches with a large number
of twigs.
12
Electrical mains supply
impedance Zmax (W)
0,21
0,21
0,19
g
a
r
d
e
n
s
h
r
e
d
d
e
r
g
a
r
d
e
n
s
h
r
e
d
d
e
r
How to shred garden and kitchen waste with hight water con-
tent and a tendency to clog
to prevent the machine from clogging, alternate waste with
−
wood containing material.
Do not allow the shredded material to pile up too high in the
area of the ejection opening. This can lead to shredded mate-
rial blocking the ejection channel, and backing up to the filler
opening.
Clean out the filler opening and ejection channel thoroughly if
the machine becomes blocked. Before doing this, switch the
motor off and disconnect the machine from the mains power
supply.
Please do not exceed the maximum branch diameter speci-
fied (cutting fresh wood) for your appliance (∅ see "Technical
data"). Depending on the wood's nature and freshness the
maximum branch diameter the machine can process may be
smaller.
The cutter automatically draws the shredding material into the
machine through the slow rotation of the cutting rollers.
Automatic switch-over in the direction of rotation:
If the unit suddenly clogs, the blades may start to turn in the
opposite direction and push the shredded material back out.
Switch off unit
−
Wait until the blades come to a standstill
−
Switch unit back on and use material which is easier to
−
process.
If the machine is overloaded, a protective motor switch en-
sures that the machine turns itself off automatically.
Turn the shredder on again after about 5 minutes.
−
If you cannot turn on the machine after this waiting time re-
−
fer to „Operational faults".
A
d
j
u
s
t
i
n
g
t
h
e
A
d
j
u
s
t
i
n
g
t
h
e
It is possible to adjust the counter blade (B) at the cutting roller
(A) free of clearance. For an effective operation, an as small as
possible clearance should be maintained.
Soft material or wet branches may tear instead of being cut. A
counter blade that is worn after repeated use may also lead to
this problem.
f
i
x
e
d
c
o
u
n
t
e
r
b
l
a
f
i
x
e
d
c
o
u
n
t
e
r
b
l
a
d
e
d
e
Publicité
Chapitres
Table des Matières
