Practical Advice; Maintenance And Servicing; Maintenance And Cleaning; After-Sales Service And Advice On Using Products - Bosch GSR 18V-60 FC Professional Notice Originale

You can preselect two speed ranges with the gear selector
(4).
First gear:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Second gear:
High speed range; for working with a small drilling diameter.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
Switching on/off
To start the power tool, press and hold the on/off switch
(10).
The worklight (8) lights up when the on/off switch (10) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
The worklight (8) will remain lit for approximately ten
seconds after the on/off switch (10) has been released.
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (10) to varying extents.
A light pressure on the on/off switch (10) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the mounting (1), are locked
when the on/off switch (10) is not pressed.
This allows screws to be driven in even when the battery is
discharged and enables the power tool to be used as a
screwdriver.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the power output is
reduced or the power tool is switched off. The power tool
will not run at full power output again until the permitted bat-
tery temperature has been reached.
Connectivity functions
In conjunction with the GCY 30-4 Bluetooth
Module, the following connectivity functions are available for
the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the GCY 30-4 Bluetooth
Battery charge indicator (battery model GBA 18V...)
(see figure A)
The three green LEDs of the battery charge indicator (18) in-
dicate the state of charge of the battery (6). For safety reas-
ons, it is only possible to check the state of charge when the
power tool has been stopped.
Bosch Power Tools
®
Low Energy
®
Low Energy Module.
Press the button (19) to show the state of charge. This is
also possible when the battery is removed.
LEDs
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
If no LED lights up after pressing the button (19), then the
battery is defective and must be replaced.

Practical advice

With the GCY 30-4 Bluetooth
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
When drilling into metal, only use sharpened HSS drills (HSS
= high-speed steel) which are in perfect condition. The
Bosch accessory range guarantees appropriate quality.
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.

Maintenance and Servicing

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.

After-sales service and advice on using products

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
English | 19
Capacity
≥ 66%
≥ 33%
<33%
Reserve
®
Low Energy Module, the
1 609 92A 4RU | (31.10.2018)