Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
- Remove the
front outlet grate together with the
lower housing panel by pulling them out from
the top.
- Remove the filter from the front.
- Release the filter retainer in the centre of the
filter (refer to Fig. 2).
- Remove the filter retainer from the old filter and
install it on the new filter medium. Make sure
the retainer sits properly and securely to pre-
vent the filter from working itself loose during
operation.
- Now reinstall the filter in the unit and reinstall
the front housing and the outlet grate.
Please only use our specially manufactured ori-
ginal filters otherwise proper operation of the
unit cannot be ensured. We cannot assume liabi-
lity for any damages or performance reductions
resulting from the employment of other filters.
We recommend thoroughly cleaning the unit whe-
never the filter is replaced.
C a r i n g f
o r t h e U n i t
If the unit is operated
be cleaned at regular intervals. Proceed as
follows:
-
Unplug the
unit's power cord from the mains
outlet!
-
Pull the outlet grate upwards and out of the unit.
-
Visually inspect the evaporation filter and
replace it as required (refer to "Filter
Replacement").
-
Now pull the lower housing panel upwards and
out of the unit.
-
Remove the filter from the front.
-
Next remove the water reservoir from the front.
Take care not to damage the water level elec-
trodes when removing the reservoir.
-
Empty the water reservoir.
-
Using a damp cloth or sponge, clean the water
reservoir and, if necessary, the inside of the
unit. Rinse the reservoir with clean water.
-
Now reinstall the water reservoir by gently lift-
ing the water level electrodes and carefully
reinserting the reservoir.
-
Then reinstall the evaporation filter and rein-
sert the housing panel and the outlet grate from
the top of the unit.
-
Reconnect the unit to the mains power supply
(the indicator goes on), and switch the unit on.
-
Refill the humidifier with water. Observe the fill
level indicator on the operator panel.
Do not overfill the unit!
Before opening the unit, unplug the power cord from the mains outlet!
continuously, it should
A n n
u a l C l e a n i n g
In order to ensure continuous, hygienic op-
eration, the unit must be cleaned annually.
Proceed as follows:
1.
Remove the filters
bed in Fig. 1 and 2. Visually inspect the fil-
ters for contamination and lime deposits.
Replace the filters as required.
2.
Remove the evaporation filter's frame and
use a cloth to clean off any dirt or lime
deposits. It may be necessary to employ a
lime removing agent.
3.
Remove the water reservoir from the unit,
taking care not to damage the water level
electrodes. If the electrodes are excessively
contaminated, use the coarse side of sponge
to thoroughly clean them.
4.
Remove all dirt and lime deposits from the
water reservoir.
5.
Wipe out the inside of the humidifier with a
damp cloth.
6.
Use only a damp cloth or mild cleansers to
clean the outside of the unit. Acidic or alka-
line cleansers can result in damage to the
unit's exterior cladding.
A
u t o m a t i c Wa t e r
R e p l e n i s h m e n t
(Optional
accessory)
When commissioning units equipped with
matic water replenishment, you must add
approx. 5 litres of water to the reservoir by hand.
The automatic replenishment function will not
begin operating until you perform this manual
"priming". When connecting the unit to the water
source, use a safety pressure house (3/4" coup-
ling) and our water monitor
(max. water pressure: 10 bar).
The connections may only be made by an au-
thorised, qualified tradesman.
To r e o r d e r
Evaporation filter disk B250
Air filter B250
from the unit as descri-
auto-
(part-no.: 2625)
(part-no.: 2626)
7
Publicité
Table des Matières
