Bosch PCM 8 S Notice Originale page 31

OBJ_BUCH-557-006.book Page 31 Wednesday, October 15, 2014 9:24 AM
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a =3.5 m/s , K=1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
cluding their amendments and complies with the following
standards: EN 61029-1, EN 61029-2-9, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 17.10.2014
Bosch Power Tools
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Dust bag 1
– Locking knob 13
– Extension bar 19 (2x)
– Fastening kit for extension bar 40
(2 U-profiles with screws)
– Saw-table extension 39
– Length stop 38
– Quick-action clamp 49
– Hex key/cross-head screwdriver 20
– Batteries (3x, size LR03, 1.5 V)
for machine versions with base unit:
– Base unit 42
(16 Profiles, 4 end caps)
– Fastening kit for base unit 43
(24 screws with nuts for assembly, 4 screws with nuts for
fastening of the machine, 4 washers)
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Mounting Individual Components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packaging material from the machine and the
accessories provided.
– For easier working when mounting the supplied product
features, please observe that the machine is in the trans-
port position.
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Angle gauge
– Box-end or open-end spanner (size 12 mm)
for assembly of the base unit
– Box-end or open-end spanner (size 14 mm)
for the lock nuts of the depth stop
– Box-end or open-end spanner (size 10 mm)
for basic adjustment of the bevel angles (vertical)
English | 31
1 609 92A 0VP | (15.10.14)