Publicité
Les langues disponibles
Les langues disponibles
USA
GB
22660
DR Railbus VT 133 525
THE PROTOTYPE
The Priegnitzer Kreiskleinbahnen
bought two narrow gauge railbuses
from the Wismar Coach Works in
1939. The distinctive Wismar design
featured twin motors with controls at
both ends of the railbus. This elimi-
nated the need to turn the railbus at
the end of the line, making it popular
with narrow gauge and short line rail-
ways. From 1932 to 1941, Wismar
produced these railbuses in a wide
variety of gauges, from 750 mm to
standard, for railways across Europe.
THE MODEL
This detailed replica features:
- weather-resistant construction
- opening doors
- four-way power control switch
- protected gearbox with seven-pole
Bühler motor
- four powered wheels
- four power pickups
- voltage stabilization circuit
- automatic directional lanterns
- interior lighting
- length: 450 mm (17.7 in.)
- weight: 1760 g (3.9 lb.)
THE PROGRAM
With this model, we recommend the
following items:
- 50550 Station Light, Single
- 50560 Station Light, Double
- 51420 Tourist Figures, Seated
- 52290 Porter Figures, Luggage
- 52390 Passenger Figures, Seated,
Set 2
10
- 52450 1900s Figures, Seated, Set 2
For information on the complete LGB
program, see the LGB catalog.
OPERATION
Operating Modes
This model has a four-way power
control switch mounted under the
floor (Fig. 1, 2):
Position 0: All power off
Position 1: Power to lights
Position 2: Power to lights and
motor
Position 3: Same as 2, but without
taillights (factory pre-set)
Multi-Train System
The model is equipped a factory-
installed onboard decoder for the
LGB Multi-Train System. It can be
used without modifications on ana-
log or digital layouts. For operation
with the Multi-Train System, the
model is programmed to loco address
03. For information on programming
the loco address, see the instructions
for various MTS components.
When operating with the Multi-Train
System, you can remotely control the
loco's functions. Press the lighting
button ("9" with remotes) to turn the
loco lights on or off. Press the func-
tion button ("1") to turn the interior
lights on or off.
When operating with the Multi-Train
System, the loco features a "Back-
EMF" function. This keeps the motor
speed constant (and under normal
conditions the loco speed), even
when the load of the loco changes,
for example, in curves or on grades.
This feature does not work at top
speed, because additional voltage
must be available to overcome any
added load.
If desired, numerous functions of the
onboard decoder, such as accelera-
tion, braking, direction of travel and
many others, can be programmed
using a PC and the 55045 MTS PC
Decoder Programming Module (see
"Instructions for advanced users").
These function can be programmed
from the 55015 Universal Remote as
well.
Power Supply
Attention! For safety and reliability,
operate this model with LGB power
supplies (transformers, power packs
and controls) only. The use of non-
LGB power supplies will void your
warranty.
Use this model with LGB power sup-
plies with an output of at least 1
amp. For more information on LGB
power supplies for indoor, outdoor
and multi-train operation, see the
LGB catalog.
Attention! After extended operation,
this model may leave carbon dust or
other debris around the track. This
dust and debris can stain carpet and
other materials. Consider this when
setting up your layout. Ernst Paul
Lehmann Patentwerk and LGB of
America are not liable for any dam-
ages.
SERVICE
Do-It-Yourself Service Levels
Level
- Beginner
Level
- Intermediate
Level
- Advanced
Attention! Improper service will void
your warranty. For quality service,
contact your authorized retailer or an
LGB factory service station (see
Authorized Service).
Hint: Additional expert instructions
for many LGB products are available
at www.lgb.com.
Lubrication
The axle bearings should be lubricat-
ed occasionally with a small amount
of LGB Maintenance Oil (50019).
Cleaning
This model can be cleaned externally
using a mild detergent and gentle
stream of water. Do not immerse this
model.
Replacing the light bulbs
Front and rear lanterns:
We recommend installation of these
parts at an authorized LGB service
station. For quality service, contact
your authorized retailer or an LGB
factory service station (see Author-
ized Service).
Interior lights
:
- Remove the main roof panel by
pushing up on the panel with a fin-
ger through an opening door.
- Carefully pull the lighting circuit
board off the mounting posts.
- Replace the bulbs.
- Reassemble.
Maintenance parts
50019 Maintenance Oil
51020 Gear Lubricant
62206 20640-Series Motor
63120 Brushes, Assembled
14 mm and 16 mm,
8 pieces
68511 Plug-In Bulb, Clear, 5 V,
10 pieces
68512 Plug-In Bulb, Red, 5 V,
10 pieces
11
Publicité
