Specifications; Legal Notices; Fcc Warning - Insignia NS-R5100 Guide De L'utilisateur

Insignia NS-R5100 AV Digital Home Theater Receiver
Category Problem
Poor FM 1 No antenna is
reception connected.
2 The antenna is not
positioned for the
best reception.
Continuous Weak signals.
hissing
noise during
FM
reception,
especially
when a
stereo
broadcast is
received.
Continuous Noise is caused by
or motors, fluorescent
intermittent lamps, or lightning.
hissing
noise during
AM
reception,
especially at
night.
Remote 1 Batteries are not
control unit loaded or are
does not exhausted.
operate.
2 The remote sensor
is obstructed.

Specifications

Note
• Design and specifications are subject to
change without notice.
• Weight and dimensions shown are
approximate.
• Specifications and external appearance may
be changed for the sake of improvement.
Amplifier Power output, stereo mode, 6 Ω, THD 0.7%,
40 Hz~20 kHz: 2×100 W
Total harmonic distortion, 6 Ω, 100 W, 1 kHz: 0.09%
Intermodulation distortion, 60 Hz, 7 kHz= 4:1 SMPTE,
6Ω, 100 W: 0.1 %
Input sensitivity, 47 kΩ, Line (CD, TAPE, VIDEO):
280 mV
Signal to noise ratio, IHF "A" weighted, Line (CD, TAPE,
VIDEO): 92 dB
Frequency response Line (CD, TAPE, VIDEO),
20 Hz~50 kHz: +0 dB, -3 dB
Output level
TAPE REC, 2.2 kΩ: 280 mV
PRE OUT (Subwoofer), 1 kΩ:1.0 V
Bass/Treble control, 100 Hz/10 kHz: ±10 dB
Surround mode, only channel driven
Front power output, 6Ω, 1 kHz, THD 0.7%: 125 W /
125 W
Center power output, 6Ω, 1 kHz, THD 0.7%: 125 W
Surround power output, 6Ω, 1 kHz, THD 0.7%:
125 W / 125 W
Digital Sampling frequency: 32, 44.1, 48, 96 kHz
Audio
Digital input level
Coaxial, 75Ω: 0.5 Vp-p
Optical, 660 nm: -15~-21 dBm
Possible Solution
1 Connect an
antenna.
2 Change the position
of the antenna.
1 Change the position
of the antenna.
2 Install an outdoor
FM antenna.
1 Keep the receiver
away from noise
sources.
2 Install an outdoor
AM antenna.
1 Replace the
batteries.
2 Remove the
obstacle.
www.insignia-products.com
Video Video format: NTSC
Input sensitivity (=Output level), 75Ω
Video (Composite (normal)): 1 Vp-p
S-Video (luminance signal): 1 Vp-p
(chrominance signal): 0.286 Vp-p
Component video (R-Y signal): 0.5 Vp-p
(B-Y signal): 0.5 Vp-p
(Y signal): 1.0 Vp-p
FM Tuner Tuning frequency range: 87.5~108 MHz
Usable sensitivity, THD 3%, S/N 30 dB: 12.8 dBf
46 dB quieting sensitivity, mono/stereo: 20.2 / 45.3 dBf
Signal to noise ratio, 65 dBf, mono/stereo: 55 / 50 dB
Total harmonic distortion, 65 dBf,1 kHz, mono/stereo:
0.5 / 1.0%
Frequency response, 30 Hz~12 kHz: ±3.0 dB
Stereo separation, 1 kHz: 30 dB
Capture ratio: 4 dB
IF rejection ratio: 80 dB
AM Tuning frequency range: 520~1710 kHz
Tuner
Usable sensitivity: 500 µV/m
Signal to noise ratio: 40 dB
Selectivity: 25 dB
General Power supply: 120 V ~ 60 Hz
Power consumption: 3.8 A
Dimensions (W×H×D, including protruding parts):
17-3/8×5-1/2×14-3/4 inches (440×141×376 mm)
Weight (Net): 20.5 lbs (9.3 kg)

Legal notices

FCC Part 15
This device complies with Part 15 of the FCC Rules.
Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within
the limits for a class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for
help.

FCC warning

Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules could
void the user's authority to operate this equipment.
Canada ICES-003 statement
This Class B digital apparatus complies with Canadian
ICES-003.
21