Peach PS500-55 Mode D'emploi page 10

Installation / Commissioning
Make sure that the main switch A is set to position "0".
It is recommended to equip the waste bin K with a
suitable waste bag (2 pieces are included in the service
pack). This makes it easier to empty the filled waste
basket.
Connect the mains cable J to a normal 230 volt socket.
Pull the paper tray extension N out of the machine by
reaching into the hole.
In the first applications it can happen that residual
lubricant may evaporate. If you should notice a slight
smell of fire or small clouds of smoke in a new device,
you can continue to work normally. If this still happens
even after a long period of use, please contact technical
support.
Manual operation
Set the main switch 1 to position "1". Now press the On/
Off button 4 on the control panel, the LED "READY" 3
lights up.
When inserting paper, the machine starts automatically
and stops as soon as all paper has passed through.
The cutting capacity is 6 sheets (80 g/m
card. However, you should only destroy paper or credit
cards, otherwise the device may be overloaded.
Never attempt to shred sealed envelopes. This can cause
damage to the cutterbar. Empty envelopes and unfold the
contents completely before you shred them. Rubberized
envelopes, labels or other products with adhesive must
NEVER be crushed as this may cause paper jams.
Do not shred wet paper, carbon paper or plastic bags.
The debris jams the cutterbar, which can lead to jams
and reduced performance of the unit.
Automatic paper shredding
Set the main switch 1 to position "1".
You can destroy a maximum of 130 A4 sheets (80 g/
2
m ) using the automatic paper feeder. Open the paper
tray cover 12 by pressing button 15 and insert the paper
smoothly into the paper tray 13. Close the paper tray
cover 12 and press the On/Off button 4, the "READY"
LED 3 lights up and the machine now begins to destroy
the inserted paper. You can interrupt this process at any
time by pressing the On/Off key 4.
Note: Depending on the amount of paper in the paper
feeder, the condition of the paper, its moisture and
other parameters, it takes 10 to 30 seconds before the
shredding process starts.
Note: During the automatic shredding process, it is not
possible to manually insert additional paper through the
cutting opening 2.
5
Credit card destruction
Set the main switch 1 to position "1". Press the On/Off
button 4 on the control panel, the LED "READY" 3 lights
up. Insert the credit card into the cutting opening 2, at
the position 16 indicated on the machine. The machine
starts automatically and stops as soon as the credit card
has passed through.
BUG FIXING
Overheating:
If you use the unit for more than 30 minutes without
interruption with maximum load, it will automatically
switch off. The "Overheat" G signal lamp lights up. After
a waiting time of approx. 15 minutes, the device can be
used again.
Door open:
If the wastebasket K is not fully inserted or the paper
tray cover L is not closed properly, the open-door
indicator lamp I will light up. Insert the wastebasket
K properly into the machine and/or press the paper tray
cover L down until it clicks into place with a "click"
2
) or 1 credit
sound.
Paper jam during manual feeding:
In the event of a paper jam, the machine stops
automatically and starts reverse running. The paper is
released again. The signal lamp Overheat G blinks.
Remove the paper from the unit, reduce the number
of pages, press the FWD key F and feed the reduced
amount of paper back in. If not all sheets are released,
press the REV key E
to start reverse running and remove the remaining paper.
Paper jam during automatic feed (ADF):
For shredding with the automatic feeder, the machine
is equipped with an autoprotection mechanism: If the
automatic paper feeder does not start successfully within
2 minutes, the transport rollers Q rotate backwards for
3 seconds and forwards for 5 seconds. This is repeated
3 times. If the feeder still does not start, the rollers rotate
for another 20 seconds.
If the shredding process still cannot start then the
machine stops and the LED Bin Full H starts to flash.
Proceed as follows to remedy the problem: Open the
paper tray cover L and clean the transport rollers Q
with a damp cloth. Reduce the amount of paper, close the
paper tray cover L, press the On/Off key 4 and start the
operation again.