Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPERATION
To reduce the risk of explosion,
WARNING
electric shock and property
damage, do not use on live electrical lines. Tool
is NOT insulated. Contact with a live circuit
could result in severe injury or death. Turn off power
before making a cut. Never cut gas or water lines.
Keep hands away from all cutting edges and
moving parts. Laceration and amputation
can occur.
Always remove battery pack before changing or
removing accessories. Only use accessories spe-
cifically recommended for this tool. Others may be
hazardous.
To reduce the risk of injury, wear safety goggles or
glasses with side shields.
Remote Cutting
• Before cutting, ensure blades are properly installed.
• To set the tool on the ground, rotate the cutting head
180° to use the front handle as a "foot" and set the
tool in position on the ground.
• To hang the tool, use the front handle and tool
hanger to set the tool in a hanging position.
• Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades.
Per NFPA 70E
All steps must be completed in order! Once started,
steps 1-4 must be completed with no more than
5 minutes between each step. If more than 5 minutes
ON THE TOOL:
Turn ON (I) the remote cut
occurs, reset (see step 7) and begin again.
switch on the tool.
1. Turn ON (
Remote cut light steady red.
the tool to disable the trigger and turn
4.
2
on the wireless function.
sec
The tool's remote cut light will be
steady red.
2. WARNING! Ensure the remote
cut switch is ON before pulling
Press and hold button 2 for
the trigger.
2 seconds.
Light 2 steady red.
Pull the trigger (1) and slide the
Light 3 flashing red.
trigger lock to
The tool's remote cut light will
be flashing red.
WARNING! During the cut, remain outside the arc
flash boundary in accordance with NFPA 70E for the
system being cut.
3. Turn ON (I) the remote.
Light 1 will be steady
blue.
Light 2 will be flashing
red.
NOTE: Light 1 flashing
blue and Light 2 off indicates the remote is
out of range of the tool. Move the remote
closer to the tool.
4. Press and hold button 2 for
2 seconds.
Light 2 will be steady
red.
Light 3 will be flashing
red.
5. Within 20 seconds, press and
hold button 3 for 2 seconds
to begin the cut.
Light 3 will be steady
red.
Release button 3, cutting will begin.
Note, if more than 20 seconds passes between
step 4 and 5, reset (see step 7) and begin again.
6. When the cut is complete, the
cut indicator will light:
Green = Done Cutting
Red = Cut Failed
7. To reset, pull the trigger (1) to
unlock.
Pull the release trigger (2) to
reset the jaws.
Turn OFF the remote cut switch
(3).
5
2
1
Pull the trigger and
slide the trigger lock to
.
) the remote cut switch on
Remote cut light flashing red.
5.
2
sec
To make the cut, press and
hold button 3 for 2 seconds.
Light 3 steady red.
Release button 3, cutting will begin.
(2).
sec
Turn
ON (I) the remote.
Press and hold button 2 for
Light 1 steady blue.
2 seconds.
Light 2 flashing red.
Light 2 steady red.
Light 3 flashing red.
6.
2
sec
When the cut is complete, the
2
cut indicator will light:
Green = Done Cutting
1
Red = Cut Failed
2
sec
2
sec
1
2
3
To m
hold
Ligh
Rele
7.
6.
TO
Pu
Pu
re
re
Publicité
Table des Matières
