Manual Mode; Important - Ferplast SWING MICROCHIP Mode D'emploi

Glass doors (Fig.4).
Warning! Cutting glass can be dangerous. You must consult a glass merchant before starting the
job. It is impossible to drill holes in toughened safety glass or double-glazing unless they have
already been drilled when the panes are manufactured.
A Measure the belly height of your pet from the floor and position the template (side A) on
the door with the bottom at the same height.
B Mark the bottom side using a marker, you will use it as the base to center the compasses on
the points marked on the template. Then drill a circular hole with radius of 108 mm. (The
centre of the hole is marked on the template).
The biggest job is done. Go to paragraph "FIT THE FLAP".
Metal doors
Follow the same instructions as those for wooden doors. The only difference lies in the fact
that the electronic system does not work near metallic objects. It is to be isolated using a
non-metal material (wood or similar), which must have a minimum thickness of 50 mm
around the entire perimeter. This prevents any interference and ensures the correct
operational efficiency of the magnetic mechanism. The biggest job is done. Go to paragraph
"FIT THE FLAP".
Walls
Follow the same instructions as those for wooden doors. (Jobs B-C-D are to be done using
suitable tools). The tunnel supplied can be installed in walls with a thickness of more than 55
mm. In this case the tunnel must be extended in cement plastering or by purchasing the
special plastic extension (TUNNEL EXTENSION Fig.10) available as accessory for the SWING
flaps range. The biggest job is done. Go to paragraph "FIT THE FLAP".
Warning! Do not cut the tunnel of the SWING MICROCHIP flap because it contains delicate
mechanism!
FIT THE FLAP (Fig.5).
Position the flap on the hole and using a marker, mark the positions where the screws are
required. Remove the flap and drill 4 holes using a drill with a 4.5 mm bit. (Warning! The
4-way locking system is to be fitted on the inner side of the door). Fit the flap and secure it with
the screws supplied, which may have to be cut and filed to remove any sharp edges. 4 short
screws are supplied for fitting to glass doors and fly screens and 4 long screws for all other
installations on a thickness of up to 55 mm. The 4 long screws will have to be shortened for
installations on an intermediary thickness (i.e.: for installations on a thickness of 45 mm
shorten the screws by 10 mm; for installations on a thickness of 35 mm shorten the screws by
20 mm, and so on). Instead, you could purchase a new set of screws to your specifications at
your local hardware store. Too short a screw could strip the thread whereas too long a screw
could break the front panel of the pet door. To finish the job, cover the screw holes using the
plugs supplied, making sure to match the rib to the seat.
INSERT THE BATTERIES (Fig.6).
When the flap is fitted you can insert the batteries in their compartment; the flap requires n°6
1,5V AA LR6 batteries. We recommend using only good quality alkaline batteries, in order to
ensure the product efficient working. Introduce the batteries in the correct way and wait for
10 seconds. If any microchip has not been previously recorded the led will start flashing with
cycles of 3 consecutive flashes. Low batteries warning: a low batteries indicator will flash
once every 5 seconds requiring the replacement with new batteries.
YOUR SWING MICROCHIP FLAP IS NOW READY TO USE!
MICROCHIP RECORDING (Fig.7).
To record your cat microchip press the memory button just once, approach your cat to
the flap and the code will automatically be recorded (you'll hear the door unlocking).
Since then, every time your cat gets near the flap the device will identify him allowing the
entrance. The recording time lasts 10 seconds maximum. To record more microchips,
following the instructions in the same order.
MEMORY DELETING
If you need to delete the product memory, it is sufficient to press the memory button for 10
seconds and it will go back to the initial conditions (the led will activate with cycles of 3
consecutive flashes).

MANUAL MODE

If you do not wish to use the electronic system, the cat flap can be converted to work
manually. To do so, press the memory button twice and the electronic system will be
excluded. By pressing again the button (just once) the product will reactivate the electronic
working keeping the previously recorded microchips.
CLEANING: QUICK AND EASY (Fig.9).
The product does not require any special maintenance, just an ordinary cleaning of the flap
(A) and of the infrared detectors placed inside the tunnel (B), at the left and right side, by
using a soft and dry cloth.

IMPORTANT

Within the European Union the barred rubbish container symbol indicates that the product,
at the end of its lifecycle, needs to be sent to separate collection point for electrical and
electronic waste and cannot be disposed of together with domestic solid waste. To ensure
correct product disposal, please dispose of this product in compliance with the law
provisions of the country where the product is found.
WARRANTY
Ferplast guarantees SWING MICROCHIP and all its parts and accessories within the limits
provided for in this paragraph and the legal regulations currently in force. The guarantee
only covers manufacturing defects and provides for free repair or replacement. The
guarantee does not cover damage and/or defects caused by carelessness, wear and tear,
usage not in accordance with the instructions and warnings in this booklet, accidents,
tampering, improper use, incorrect repairs and purchases not confirmed by receipt.
GB
IT
FR
D
NL
ES
PT
SK
CS
HU
SV
DA
PL
RU