Boma ASPIRO WET 30 Manuel D'utilisation Et D'entretien page 11

• Loosen the latch hinges of the vacuum head (Fig.06) and remove it (Fig.07).
• Fig.10).
N.B:
• Empty the collection tank.
N.B:
• Fig.08) and the vacuum head (Fig.09).
• Start work again.
N.B:
Cleaning wet surfaces
the off position (Fig.04).
2. Check that the plug on the power cable is connected to the power supply socket, otherwise
disconnect it.
WARNING:
3. Free the vacuum head (Fig.06
N.B:
N.B:
5. Secure the vacuum head to the collection tank (Fig.09-10).
6. Plug the power cable into the mains socket.
ATTENTION:
7. Switch on the appliance by positioning the vacuum motor switch to position "I" (Fig. 4).
N.B:
8. Start work.
If when working a reduction in the vacuuming power is noted or the noise of the appliance becomes
•
• Remove the plug from the power socket.
WARNING:
• Loosen the latch hinges of the vacuum head and remove it (Fig. 6-7).
• Empty the collection tank.
N.B:
• Fig.13
• Fig.12).
• Reassemble the vacuum head (Fig.9-10).
• Start working again.
Take the appliance to the designated machine storage place after work is completed.
ATTENTION:
EMPTYING THE COLLECTION TANK
At the end of the work, and before carrying out any type of maintenance, perform the following
Take the appliance to where its collection tank is emptied.
N.B
CAUTION
2.
the off position (Fig.04).
3. Check that the plug on the power cable is connected to the power supply socket, otherwise
disconnect it.
WARNING:
Free the vacuum head (Fig.06) and lay it on the ground.
5. Empty the collection tank.
N.B:
N.B:
6.
Take the device to its maintenance area.
CAUTION
2.
the off position (Fig.04).
3. Check that the plug on the power cable is connected to the power supply socket, otherwise
disconnect it.
WARNING:
Fig.11).
Free the vacuum head (Fig.06) and lay it on the ground.
5.
6.
N.B:
Fig.12).
7.
8.
N.B:
This chapter lists the most common problems linked with the use of the appliance. If you are unable
to resolve the problems with the information given here, please contact your nearest assistance
centre.
PROBLEM
Fig. 4).
Fig.14).
To dispose of the appliance, take it to a demolition centre or an
authorised collection centre.
separate out the following materials, then send them to the
appropriate collection centres in accordance with applicable
• Electric and electronic parts*
• Plastic parts
• Metallic parts
(*) In particular, contact your distributor when scrapping electric and
electronic parts.
11
MAINTENANCE
Fig.11).
Fig.13).
TROUBLESHOOTING
POSSIBLE CAUSE
The main switch is not activated. Press the main switch.
The plug on the appliance's power
Connect the plug on the appliance's
cable has not been correctly
power cable to the mains socket.
inserted into the mains socket.
Check that the technical data on
the appliance do not match the
the appliance's serial number plate
match the data of the mains supply.
supply network.
Contact a specialised technician
The power cable is damaged.
immediately.
The vacuum hose is not connected
Connect the vacuum hose correctly
correctly to the nozzle on the
to the nozzle on the collection tank.
collection tank.
The vacuum hose is not connected Connect the vacuum hose correctly
correctly to the extension hose. to the extension hose.
The extension hose is not Connect
connected correctly to the vacuum correctly to the vacuum accessory
accessory being used. being used.
The vacuum circuit is blocked
Remove the obstruction in the
(vacuum hose; extension hose;
vacuum circuit.
vacuum accessory).
There is a blockage in the vacuum Clear the obstruction in the vacuum
DISPOSAL
Fig.14).
SOLUTION
the extension tube