Boma ASPIRO WET 30 Manuel D'utilisation Et D'entretien page 10

SYMBOLS USED IN THE MANUAL ..........................................................10
ENVIRONMENT PROTECTION .................................................................10
TECHNICAL DATA TABLE KEY ................................................................10
COMPLIANT USE .......................................................................................10
PARTS OF THE APPLIANCE .....................................................................10
INITIAL OPERATION OF THE APPLIANCE ..............................................10
EMPTYING THE COLLECTION TANK ......................................................11
MAINTENANCE ..........................................................................................11
TROUBLESHOOTING ............................................................................... 11
EC DECLARATION OF CONFORMITY .....................................................24
TECHNICAL DATA .....................................................................................25
and keep them for future use or for possible resale of the appliance.
•
• Failure to follow the operating instructions and safety standards can cause damage to the
appliance and present a danger to the user and other people.
• Any transport damage should be reported immediately to your dealer.
SYMBOLS USED IN THE MANUAL
Open book symbol with an "i":
Indicates the need to consult the instruction manual.
Open book symbol:
Tells the operator to read the manual before using the appliance.
Covered place symbol:
the operations preceded by this symbol must always be carried out in a dry, covered area.
Symbol i:
Indicates additional information for the operator, to improve the use of the device.
ENVIRONMENT PROTECTION
All packaging is recyclable. The packages must not be discarded in household waste, but
delivered to the relevant collecting centres.
Old appliances contain valuable recyclable materials and must be delivered to the
the environment. Please dispose of old appliances via the separate collection systems.
TECHNICAL DATA TABLE KEY
W=Dust; WD= Wet & Dry
PP=Polypropylene ; Acc= Steel
Nominal voltage (V) and frequency (Hz) of the vacuum motor in the appliance.
Number of vacuum motors.
Nominal output (W) and type of suction.
Vacuum (mmH O and kPa).
2
3
/h).
Total capacity of the collection tank (l).
Collection tank useful capacity (l).
Power cable of the appliance (cm).
Appliance dimensions [length x width x height] (cm).
Weight of single appliance (Kg).
COMPLIANT USE
WARNING: The appliance is not suitable for vacuuming powders that are harmful to health.
•
• This appliance is suitable for commercial, professional and industrial use, such as workshops,
industries, schools and hotels.
•
PARTS OF THE APPLIANCE
Vacuum head.
2. Handle bar for vacuum head lifting.
3. Vacuum motor control switch.
Power cable.
5. Power cable plug.
6. Power cable support.
7.
8.
Vacuum cap fastening hook.
Collection tank.
Nozzle.
Vacuum hose release button .
Handle.
Collection tank support trolley.
Pivoting wheel.
Rear wheel.
Trolley control handlebars .
INITIAL OPERATION OF THE APPLIANCE
N.B.
2. Open the outer box.
3. Remove the accessories from the box and carefully lay them on the ground.
Remove the appliance from the packaging.
N.B.:
CAUTION
DANGER
5. Insert the vacuum hose into the nozzle on the collection tank, press the button on the nozzle and
insert the vacuum hose fully (Fig.05).
6. Connect the extension pipe to the vacuum hose.
7. Choose the most suitable attachment for the work to be carried out and connect it to the
extension pipe.
Dry cleaning
the off position (Fig.04).
2. Check that the plug on the power cable is connected to the power supply socket, otherwise
disconnect it.
WARNING:
3. Free the vacuum head (Fig.06
N.B.:
N.B:
Secure the vacuum head to the collection tank (Fig.09-10).
5. Plug the power cable into the mains socket.
ATTENTION:
6. Switch on the appliance by positioning the vacuum motor switch to position "I" (Fig. 4).
N.B.:
7. Start work.
If the "combined nozzle" accessory is used, set the switch in the brush to "HARD SURFACE" or else
"CARPET FLOORS". Proceed with the vacuuming.
N.B:
ATTENTION:
If when working a reduction in the vacuuming power is noted or the noise of the appliance becomes
•
• Remove the plug from the power socket.
WARNING:
10
Fig.08).
Fig. 04).