Installation Sequence; Overheating Protection - Starmix HF Notice D'utilisation

1 Before use
We have compiled these operating instructions so that you become
familiar with your new appliance quickly and comprehensively.
The manufacturer reserves the right to carry out modifications to
the design and equipment.
Any other work not covered by this operating manual must not be
carried out.
THIS MACHINE IS PERFECT FOR VARIOUS USES, FOR
EXAMPLE IN HOTELS, SCHOOLS, HOSPITALS, FACTORIES,
SHOPS AND LIVING QUARTERS.
• Please read these instructions carefully before using this appli-
ance. It provides you with important information on its safety,
operation, maintenance and disposal.
• Familiarise yourself with your new appliance and its various
• functions following the sequence of the instructions.
• Follow all notes and explanations referring to the correct operati-
on and handling. This will ensure the continuous availability and
a long life for your appliance.
• The safety notes, in particular, must be followed. They help
you to prevent accidents and to protect your appliance from
damage..
• Please keep these instructions for future reference.
2 Instructions for the wall brackets
To be fitted by a qualified expert taking due consideration of
existing national safety regulations. In rooms containing showers
or baths, the wall bracket may not be fitted within the safety zone
stipulated in regulation 0100 part 701. The wall bracket should be
fitted at a height of at least 150 cm above the floor.. (→
)
distances
A = connection to wall mains wiring.
B = connection to surface mains wiring.

2.1 Installation sequence;

for fixed connection lead (A)
The connection wiring from the mains must be at least 3x1,5
mm for wall holder model WHS
2
The connection wiring from the mains must be at least 2x1,0
mm for wall holder models WH, WHR
2
10. Separate the cover (1) of the wall holder from the back plate by
loosening the screw (14).
11. Remove the knockout (2) provided in the back plate of the wall
holder.
12. Feed the mains supply cable (3) coming out of the wall into the
hole in the back plate left after removing the knockout (2).
Minimum
Original operatin instructions in German
13. Secure the back plate of the wall holder to the wall using the
plugs and screws provided.
14. Remove the terminal connector (4), connect the mains supply
cable (3) to the terminal connector (4), as shown in the picture,
and then secure again the terminal connector (4).
15. Model WH. WHR is double insulated and no earth connection
is provided..
Model WH-S the earth cable from the wall must be connected to
the terminal connector. The cables shall withstand 16A.
16. Fit the front cover of the wall holder, taking care to locate the
cable sleeve (6) properly.
17. Secure the front cover with the screw (14).
18. Switch on the general switch of your mains electricity. The
hairdryer is ready for use.
2.2 Installation sequence
for mobile connection lead (B)
WH; WHR: The connection wiring must be at least type
H05VV-F 2x1,0 mm
2
this method is not allowed for wall holder model WH-S!
L
8. Separate the cover (1) of the wall holder from the back plate by
loosening the screw (14).
9. Secure the back plate of the wall holder to the wall using the
plugs and screws provided.
10. Remove the terminal connector (4), connect the mains supply
cable (3) to the terminal connector (4), as shown in the picture,
and then secure again the terminal connector (4).
11. Fit the strain relieves (5) and (10)
12. Fit the front cover of the wall holder..
13. Secure the front cover with the screw (14).
14. Switch on the general switch of your mains electricity. The
hairdryer is ready for use.

2.3 Overheating protection

The appliance switches off automatically in the case of thermal
overload. When this happens, switch the switch to 0 or release
the push button and eliminate the external causes of overheating.
Once the appliance has cooled down it will be ready to use again in
a few minutes. Defect hairdryers may only be repaired by qualified
experts.
GB - 15