Operating Specifications; Installation Instructions - Omnifilter SFM3 Instructions D'installation

OPERATING SPECIFICATIONS

Pressure Range: 30–125 psi (2.1–8.62 bar)
Temperature Range: 40°F–100°F (4.4°C–37.8°C)
Turbidity: 5 NTU max
Model CBF2
Flow Rate: 0.5 gpm (1.9 Lpm)
Capacity: 500 gallons (1,839 liters) or
6 month cartridge life
Model SFM3
Flow Rate: 0.75 gpm (2.8 Lpm)
Capacity: 2,500 gallons (9,460 liters) or
12 month cartridge life
PRECAUTIONS
WARNING
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection
before or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
CAUTION
Filter must be protected against freezing, which can
cause cracking of the filter and water leakage.
CAUTION
Because of the product's limited service life and to
prevent costly repairs or possible water damage, we strongly
recommend that the head of the filter be replaced every ten
years. If the head of your filter has been in use for longer than
this period, it should be replaced immediately. Date the top of
any new head to indicate the next recommended
replacement date.
CAUTION
Turn off water supply to head without cartridge if it
must be left unattended for an extended period of time.
CAUTION
Do not use electrical heating tape on this unit.
NOTES:
For cold water use only.
•
The contaminants or other substances removed or reduced by
•
this water treatment device are not necessarily in your water.
Ask your local water municipality for a copy of their water
analysis, or have your water tested by a reputable water
testing lab.
Do not install where system will be exposed to direct sunlight.
•
Filter cartridge life varies depending on filter type, usage, and
•
water conditions.
The replacement filter cartridge used with this system has a
•
limited service life. Changes in taste, odor, or flow of the water
being filtered indicate that the cartridge should be replaced.
Use only OMNIFILTER replacement cartridges.
•
This installation must comply with all applicable state and
•
local regulations.
Use only Teflon tape without adhesive backing to seal joints.
®
•
Do not use pipe compound ("pipe dope"), sticks, or similar
compounds with this unit; they contain petroleum derivatives
which will cause crazing and cracking of the plastic in the
filter housing.
Use only soap and water to clean filter housing
•
and components.
Teflon is a registered trademark of IE DuPont de Nemours and Company, Corporation,Wilmington, Delaware
• 2 •
Do not use aerosol sprays (bug spray, cleaning fluids, etc.)
•
near the filter. They contain organic solvents which will cause
crazing and cracking of the plastic in the filter housing.
After prolonged periods of non-use, such as a vacation, it
•
is recommended that the system be flushed thoroughly. Let
water run for 2-3 minutes before using.
Do not use a torch near the unit.
•
Wear safety glasses during installation.
•

INSTALLATION INSTRUCTIONS

NOTE:
Please read all instructions, specifications, and precautions
•
before installing and using your water filter.
Numbered diagrams correspond with numbered steps.
•
For standard installation on 1/2-inch 14 NPS threads (most
•
common thread on kitchen faucets) cold water line.
Installation
1. Installing the Water Supply Adapter
The supply adapter fits 1/2-inch NPS supply threads. If local
codes permit, it may be used to connect the filter system
to the cold water supply line. If local codes do not permit
the use of the supply adapter, alternate connectors can be
obtained from your local retailer.
A) Turn off cold water supply line. If cold water line does not
have a shut-off valve under the sink, you should
install one.
B)
Turn on the cold water faucet and allow all water to drain
from line.
C)
Disconnect cold water line from 1/2-inch 14 NPS threaded
stub on bottom of main faucet.
D)
Apply Teflon ® tape onto threads of faucet stub and supply
adapter. Screw the water supply adapter to the threaded
faucet stub as shown.
E) Using the nut that previously connected the cold water
line to the faucet, screw the cold water line to the male
supply adapter threads.
1
D
C
E
B
A